manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Руководство по настройке программного обеспечения

Поделиться
Скачать
Cisco ASR1002 - ASR 1002 Router Скачать руководство пользователя страница 364

 

      Configuring Bridge Domain Interfaces

  Information About Bridge Domain Interfaces

4

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

  •

NTP

  •

RARP

  •

SNMP

  •

TCP

  •

Telnet

  •

TFTP

  •

UDP

Support for IP Forwarding

Bridge domain interface supports the following IP forwarding features:

  •

IPv4 input and output access control lists (ACL)

  •

IPv4 input and output QoS policies. The operations supported for the input and output service 
policies on a bridge domain interface are:

  –

Classification

  –

Marking

  –

Policing

  •

IPv4 L3 VRFs

Packet Forwarding

A bridge domain interface provides bridging and forwarding services between the Layer 2 and Layer 3 
network infrastructure.

Layer 2 to Layer 3

During a packet flow from a Layer 2 network to a Layer 3 network, if the destination MAC address of 
the incoming packet matches the bridge domain interface MAC address, or if the destination MAC 
address is a multicast address, the packet or a copy of the packet is forwarded to the bridge domain 
interface.

Note

MAC address learning cannot not be performed on the bridge domain interface.

Note

In a bridge domain, when flooding unknown unicast frames, bridge domain interface is not included.

Layer 3 to Layer 2

When a packet arrives at a Layer 3 physical interface of a router, a route lookup action is performed. If 
route lookup points to a bridge domain interface, then the bridge domain interface adds the layer 2 
encapsulation and forwards the frame to the corresponding bridge domain. The byte counters are 
updated.

Содержание ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды