Cisco ASR 901S Series Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 106

background image

10% to 85%, noncondensing, ±5 %

Relative humidity

5% to 95% RH

Non-operational humidity

13,000 ft (4000 m) maximum 104°F (40°C) ambient

Meets applicable requirements Section 8 of ATIS 0600010.01.2008

Equipment operates as intended between sea-level and 6000 ft (1800
m) at 100.4°F (38°C) plus solar loading

Equipment operates as intended between 6000 ft (1800 m) and 13000
ft (3900 m) at 69.8°F (21°C) plus solar loading for the equipment with
pressure sensitive components (GR-3108 Issue 2, Class 4)

Operational altitude

13000 ft

Non-operational altitude

For the range of 9.92 to 12.84 lbs (4.5 to 9.0 kgs), target minimum
velocity change input is 83 in./sec (2.11 m/s) and effective few fall drop
height is 5.0 in. (0.127 m) (ENG-3396, Section 4.2.4)

Operational mechanical shock

For the range of 9.92 to 12.84 lbs (4.5 to 9.0 kgs) the range of peak
acceleration input (trapezoidal pulse is between 55 to 70 G , with
minimum velocity change of 166 in./sec (4.22 m/s) (ENG-3396, Section
4.3.4)

Non-operational mechanical shock

All product categories: 0.41 G

rms

from 3 to 500 Hz with spectral break

points of 0.0005 G/2/Hz at 10 Hz and 200 Hz and 5 dB roll off at each
end. (ENG-3396, Section .2.5)

Operational vibration

All product categories: 1.2

rms

from 3 to 500 Hz with spectral break

points of 0.0065 G/2/Hz. At 10 Hz and 100 Hz and 5 dB roll off at each
end. (ENG-339611. Rev2 [Test Method: IEC-682-32])

Non-operational vibration

-40°F (-40°C)

Cold start

114.8°F (46°C) plus solar radiation (optional 149°F [65°C]) (GR-3108
Issue 2, Class 4)

Hot start

Drop the unpackaged sample 3.9" onto a rigid surface. Drop 1 face, 2
edges, and 2 corners. (ENG-339611.Rev2 [Test Method: IEC-68-2-32])

Non-operational Free-Fall Drop

Dwells at resonant frequency for 100,000 cycles at 3G in each axis.

Pole mount kit non-operational
vibration

Equipment complies with earthquake tests per sections 4.4.1 and 5.4.1
of GR-63 or ANSI TI-329 (GR-3108 Issue 2)

Earthquake, Zone 4

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

OL-29732-01

85

Specifications and Part Numbers

Product Specifications

«
...
93
94
95
96
97
...
»

Содержание ASR 901S Series











































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 901S Series

Бренд: D-Link Страницы: 100

Бренд: D-Link Страницы: 134

Бренд: D-Link Страницы: 187

Бренд: D-Link Страницы: 225

Бренд: D-Link Страницы: 31

Бренд: D-Link Страницы: 35

DES-1016D - Switch

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 107

AirPlusXtremeG DI-624

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 48

Бренд: dbx Страницы: 2

Бренд: dbx Страницы: 17

Бренд: Javad Страницы: 35

Бренд: Oracle Страницы: 24

Бренд: MiLAN Страницы: 1

PacketShaper PS-S200

Бренд: Symantec Страницы: 2

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: JETWAY Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды