Cisco ASR 901S Series Скачать руководство пользователя страница 15

Страница: 15 / 106

AC power supply unit

For details about the internal interfaces available in the cable bay, see

Cisco ASR 901S Series Aggregation Services Router: Back View

The Cisco ASR 901S Series Aggregation Services Router has a conduction-cooled fanless design. The back
panel of the router acts as the heat sink for all the components.

The following figure illustrates the back view of the router, with heat sink fins.

Figure 4: Cisco ASR 901S Series Aggregation Services Router Back View

Heat sink fins

Cisco ASR 901S Series Aggregation Services Router: Top and Bottom View

At the top of the Cisco ASR 901S Series Aggregation Services Router is an antenna connector and a handle
that is used to carry or remove the router.

The antenna connector provides support for integrated or external antennas.

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

OL-29732-01

Introduction

Cisco ASR 901S Series Aggregation Services Router: Back View

Содержание ASR 901S Series











































































































Результаты поиска

Содержание ASR 901S Series

Отзывы:

Похожие инструкции для ASR 901S Series

Бренды по названию

Популярные бренды

Cisco ASR 901S Series, Руководство по установке

Результаты поиска

Содержание ASR 901S Series

Отзывы:

Похожие инструкции для ASR 901S Series

Бренды по названию

Популярные бренды