Cisco ASR 901S Series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 106

background image

Before You Begin

When powering the router with DC power, you must ensure that DC power can be conveniently removed
from the unit. The power should

not

be removed by disconnecting the DC power connector on the unit.

Procedure

Step 1

Insert shielded copper wires through the cable sleeve. A maximum of four copper wires can be used.

Step 2

Pass the cable sleeve through the cord grip body, grommet, and molded body as shown in the figure below.

Step 3

Insert each of the copper wires into the O-ring contacts (see the following table) provided and tighten the
screws into the coupling unit (holding the wires) using the special screw driver. The DC power connector
assembly is now complete.

Figure 31: Assembling the DC Power Connector

Red wire, -48 V RTN

3

Black wire, -48 V

1

Green or Yellow wire, safety ground

4

White wire (not used)

2

Step 4

Before connecting DC power to the router, ensure that the ground is connected to the router (see

the Router, on page 45

).

Step 5

Turn off all power sources to the router, including the DC power source.

Do not connect the DC power connector when the router is powered
on.

Caution

When connecting the DC power to the router, always connect the router end of the cable FIRST.
When removing the DC power connector, always disconnect the router end of the cable LAST.

Caution

Step 6

Connect the DC power connector to the DC input plug on the faceplate of the router. To power on the router,
see

Powering on the Router, on page 69

.

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

54

OL-29732-01

Installing the Router

Assembling and Connecting the DC Power Cable to the Router

«
...
62
63
64
65
66
...
»

Содержание ASR 901S Series











































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 901S Series

Бренд: D-Link Страницы: 100

Бренд: D-Link Страницы: 134

Бренд: D-Link Страницы: 187

Бренд: D-Link Страницы: 225

Бренд: D-Link Страницы: 31

Бренд: D-Link Страницы: 35

DES-1016D - Switch

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 107

AirPlusXtremeG DI-624

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 48

Бренд: NAIM Страницы: 2

Бренд: F-SECURE Страницы: 19

Бренд: H3C Страницы: 45

Бренд: H3C Страницы: 80

Бренд: H3C Страницы: 46

Бренд: H3C Страницы: 45

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды