Cisco ASR 901S Series Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 106

background image

Procedure

Step 1

To open the router cover, use the special screw driver to loosen all twelve captive screws in the order shown
in the above figure. Ensure that the screws are released from the screw thread on the router and remain on the
router cover as shown in the following figure.

Do not forcibly remove the captive screws out of the router cover. You may need to remove the
captive screws completely only when replacing a router cover.

Note

Figure 28: Router Cover, Showing Captive Screw

Captive screw loosened from the screw thread on the router

1

Step 2

After all twelve screws are loose, remove the cover. The router door is held by a cable that is affixed to the
cable bay inside the chassis as shown in the following figure.

Figure 29: View of Wall-Mounted Router With Open Cover

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

50

OL-29732-01

Installing the Router

Opening the Router Cover

«
...
58
59
60
61
62
...
»

Содержание ASR 901S Series











































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 901S Series

Бренд: Watchguard Страницы: 40

NetDefend DFL-260E

Бренд: D-Link Страницы: 328

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

DFL-210 - NetDefend - Security Appliance

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 4

Бренд: Dahua Страницы: 12

NetDefend DFL-1600

Бренд: D-Link Страницы: 23

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: Quick Eagle Networks Страницы: 4

nForce 680I LT SLI

Бренд: Nvidia Страницы: 80

Бренд: Wintech Страницы: 21

Бренд: Gbord Страницы: 8

Бренд: WAGO Страницы: 48

Network Adapter ADZIFCF

Бренд: Addonics Technologies Страницы: 1

Бренд: Juniper Страницы: 396

Бренд: Stepper Motor Canada Страницы: 5

Бренд: ALIBI Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды