Cisco ASR 901S Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 106

background image

Table 4:

Description

Name

Cisco Product ID
(PID)

This kit is required if your installation requires a Cisco mounting
bracket to mount the router. This kit is included with the router
accessory kit, and is used with the wall mount and pole mount kit
and includes the hardware required to attach the mounting bracket
onto a wall or pole clamp bracket.

Wall Mount Kit,
on page 27

A901S-MNT-WALL=

This kit is required for all pole or streetlight installations and
includes a mounting bracket, pole clamp bracket, pole clamp gusset,
and the hardware required to attach the pole clamp bracket assembly
to a pole.

Pole Mount Kit,
on page 25

A901S-MNT-POLE=

The band straps are two steel straps that are used to mount the
router on poles larger than 5 inches (14 cm) in diameter. These
straps are provided with the

Pole Mount Kit, on page 25

. A Band-It

Tool is required to install the steel straps on a pole.

Band Straps, on
page 29

This kit includes a Band-It tool that is required when using steel
straps to install the router on poles larger than 4.5 inches (11.4 cm)
in diameter.

Strap Tool Kit,
on page 29

AIR-BAND-INST-TL=

General Safety Information for Mounting

Before performing any of the tasks in this chapter, read the safety warnings in this section and the

Guidelines, on page 15

.

Two technicians are required to properly and safely mount the router.

All mounting methods at any location are subject to the acceptance of local jurisdiction.

Caution

The mounting surface, attaching screws, and optional wall anchors must be able to support 13.66 lbs. (6.2
kgs [assembled FD chassis with top cover including two SFPs, antenna, and power supply unit]) or 16.31
lbs. (7.4 kgs [assembled FA chassis with top cover including two SFPs, antenna, and power supply unit])
static weight.

Caution

Personnel mounting the router must understand grounding methods.

Caution

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

24

OL-29732-01

Installing the Router

General Safety Information for Mounting

«
...
32
33
34
35
36
...
»

Содержание ASR 901S Series











































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 901S Series

Бренд: Salusfin Страницы: 6

Бренд: Qlogic Страницы: 2

ICS-G7748A Series

Бренд: Moxa Technologies Страницы: 10

Бренд: Zonet Страницы: 2

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Бренд: Edgewater Networks Страницы: 7

Aquaduct 360 XT

Бренд: Aqua Computer Страницы: 28

ELC-LTTR240-TBP

Бренд: ENERMAX Страницы: 16

Бренд: Billion Страницы: 120

Бренд: Freescale Semiconductor Страницы: 8

NVRx-7300 series

Бренд: Swann Страницы: 9

Бренд: LevelOne Страницы: 26

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Бренд: Intel Страницы: 105

crown PIP Series

Бренд: Harman Страницы: 16

Бренд: INNOSILICON Страницы: 11

Бренд: NZXT Страницы: 2

Бренд: Hawking Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды