Cisco 3825 Series Скачать руководство пользователя страница 221

Страница: 221 / 358

A-89

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

show ip rtp header-compression

To show Real-Time Transport Protocol (RTP) header compression statistics, use the

show ip rtp

header-compression

privileged EXEC command.

show ip rtp header-compression

[

type

number

]

[detail]

Syntax Description

Command Modes

Privileged EXEC

Command History

Usage Guidelines

The

detail

keyword is not available with the

show ip rtp header-compression

command on a Route

Switch Processor (RSP). However, the

detail

keyword is available with the

show ip rtp

header-compression

command on a Versatile Interface Processor (VIP). Enter the

show ip rtp

header-compression type number detail

command on a VIP to retrieve detailed information about RTP

header compression on a specific interface.

Examples

The following is sample output from the

show ip rtp header-compression

command:

Router# show ip rtp header-compression

RTP/UDP/IP header compression statistics:

Interface Multilink1 (compression off, IETF, RTP)

Rcvd: 0 total, 0 compressed, 0 errors

0 dropped, 0 buffer copies, 0 buffer failures

Sent: 430 total 429 compressed

15122 bytes saved, 0 bytes sent

0 efficiency improvement factor

Connect: 16 rx slots, 16 tx slots, 0 long searches, 1 misses

99% hit ratio, five minute miss rate 0 misses/sec, 0 max.

type number

(Optional) Interface type and number.

detail

(Optional) Displays details of each connection.

Note

This keyword is not supported on the Cisco 3825 router.

Release

Modification

11.3

This command was introduced.

12.1(5)T

The command output was modified to include information related to the
Distributed Compressed Real-Time Transport Protocol (dCRTP) feature.

12.2(8)MC2

This command was incorporated.

12.2(15)MC1

This command was incorporated.

12.3(11)T

This command was incorporated.

12.4(2)MR

This command was incorporated.

Содержание 3825 Series







































































































































































































































































































































































Результаты поиска

Содержание 3825 Series

Отзывы:

Cisco 3825 Series, Руководство по настройке программного обеспечения, Страница: 221 / 358

Результаты поиска

Содержание 3825 Series

Отзывы: