Cisco 3825 Series Скачать руководство пользователя страница 150

Страница: 150 / 358

A-18

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

dejitter-buffer

To specify the size of the dejitter-buffer used to compensate for the network jitter, use the

dejitter-buffer

command in the CEM configuration mode. To restore the dejitter-buffer to its default size, use the

form

of this command.

dejitter-buffer

size

no dejitter-buffer

Syntax Description

Defaults

The dejitter buffer defaults to 4 milliseconds.

Command Modes

CEM circuit configuration

Command History

Examples

The following example illustrates the use of the

dejitter-buffer

command:

Router#

config t

Router(config)#

interface cem 0/0/0

Router(config-if)#

no ip address

Router(config-if)#

cem 0

Router(config-if-cem)#

dejitter-buffer 10

Router(config-if-cem)#

xconnect 10.10.10.10 200 encapsulation mpls

Router(config-if-cem-xconn)#

exit

Router(config-if-cem)#

exit

Router(config-if)#

exit

Router(config)#

exit

Related Commands

size

Use the

size

argument to specify the size of the buffer in milliseconds.

Size

can vary from 4 to 500 ms; default is 4 ms.

Release

Modification

12.4(12)MR2

This command was introduced.

Command

Description

cem

Enters circuit emulation configuration mode.

cem class

Applies the CEM interface parameters defined in the given
<cem-class-name> to the circuit.

class cem

Configure’s CEM interface parameters in a class that’s applied to
CEM interfaces together in the global configuration mode.

Содержание 3825 Series







































































































































































































































































































































































Результаты поиска

Содержание 3825 Series

Отзывы:

Cisco 3825 Series, Руководство по настройке программного обеспечения, Страница: 150 / 358

Результаты поиска

Содержание 3825 Series

Отзывы: