Cisco 3825 Series Скачать руководство пользователя страница 201

Страница: 201 / 358

A-69

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

sample-rate

To specify in milliseconds the rate hardware samples the data on the attached circuit, use the

sample-rate

command in the circuit emulation (CEM) circuit configuration mode.

sample-rate

[

sample-rate

]

Syntax Description

Command Modes

CEM circuit configuration

Command History

Examples

The following example illustrates the use of the

sample-rate

command:

Router#

config t

Router(config)#

interface cem 0/0/0

Router(config-if)#

no ip address

Router(config-if)#

cem 0

Router(config-if-cem)#

sample-rate 2

Router(config-if-cem)#

xconnect 10.10.10.10 200 encapsulation mpls

Router(config-if-cem-xconn)#

exit

Router(config-if-cem)#

exit

Router(config-if)#

exit

Router(config)#

exit

Related Commands

sample rate

Sample rate translates into the

payload-size

sent over the circuit. The default

is 1 ms.

•

32-timeslots at 1ms = 256-bytes (32-timeslots * 8-bytes/timeslot/ms)

•

24-timeslots at 2ms = 384-bytes (24-timeslots * 16-bytes/timeslot/ms)

Release

Modification

12.4(12)MR2

This command was introduced.

Command

Description

cem

Apply CEM class.

cem class

Applies the CEM interface parameters defined in the given
<cem-class-name> to the circuit.

class cem

Configure’s CEM interface parameters in a class that’s applied to
CEM interfaces together in the global configuration mode.

Содержание 3825 Series







































































































































































































































































































































































Результаты поиска

Содержание 3825 Series

Отзывы:

Cisco 3825 Series, Руководство по настройке программного обеспечения, Страница: 201 / 358

Результаты поиска

Содержание 3825 Series

Отзывы: