manualshive.com logo in svg

Cisco 3825 Series, Руководство по настройке программного обеспечения, Страница: 17 / 358

Поделиться
Скачать
Cisco 3825 Series Скачать руководство пользователя страница 17

       

1-7

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Chapter 1      Overview of the Cisco 3825 Mobile Wireless Edge Router

    Cisco IOS Software Features

Software Features

Standard Cisco IOS software features supported in the Cisco  3825 router for the RAN-O 
implementation include:

Simple Services

  •

DHCP

  •

PPP

  •

NAT

  •

OSPF

  •

RIP

Intelligent Services

  •

QoS

  •

VPN

  •

IP Multicast

  •

Mobile IP/FA

  •

content caching

  •

MPLS

  •

L2TPv3

Other Services

  •

ACFC and PFC Handling During PPP Negotiation

  •

HSRP

  •

NTP

  •

SNMP

Redundancy Support

In a RAN-O application, to ensure availability, the backhaul links to a Cisco 3825 router are redundantly 
cabled to the Cisco 2-port T1/E1-RAN card. This card, designed specifically for the 
Cisco MWR 1941-DC-A router and Cisco 3825 router includes relays that activate the T1/E1 ports. 
These relays allow “Y” cabling for router redundancy where the T1/E1 link is not redundant and default 
to open. The relays are controlled by HSRP/redundancy protocol between the two routers connected to 
the same T1/E1.

Note

If you choose to use the Cisco 3825 router in a non-redundant configuration, you must close the relays 
on the card using the 

standalone

 subcommand. Also, redundancy parameters are processed when the 

router is booted up. These parameters cannot be changed “on the fly.”

HSRP

Cisco’s HSRP is used to control which router is active and which is standby. HSRP uses a priority 
scheme to determine which HSRP-configured router is to be the default active router. Priority is 
determined first by the configured priority value, then by the IP address. In each case, a higher value is 
of greater priority.

Содержание 3825 Series







































































































































































































































































































































































Отзывы:

Нет отзывов