Cisco 3825 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 358

Cisco 3825 Series Скачать руководство пользователя страница 16

1-6

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Chapter 1 Overview of the Cisco 3825 Mobile Wireless Edge Router

Cisco IOS Software Features

Figure 1-4

Example of Cisco 3825 Router in a Cell Site POP

Cisco IOS Software Features

There is one version of software available for the Cisco 3825 router. This version of the software is
required for implementing the Cisco 3825 router in a Radio Access Network-Optimization (RAN-O)
configuration.

Software features for the RAN-O Implementation

The software required for implementing the Cisco 3825 router consists the Cisco IOS software running
on the MIPs-based portion of the Cisco 3825 router hardware.

Cisco IOS software functions added to the Cisco 3825 router for the RAN-O implementation include:

•

Redundancy logic—For monitoring Hot Standby Router Protocol (HSRP) information to determine
the active and standby router and control T1 termination.

•

Failover logic—To force a switchover for hardware failures or an over-temperature condition.

•

Relay control—To open and close the T1/E1 interfaces on the active and standby routers.

•

Diagnostic functions—To monitor the “health” of the standby Cisco 3825 router.

GSM/GPRS/

EDGE BTS

UMTS Node B

(R4/R99)

BSC

RNC

T1/E1

Cell Site

Access Network

BSC/RNC Site

Mobile

Internet

Edge

Optimized Abis and lub over IP

Cisco
MWR

ATM
(AAL2/AAL5)

TDM

TDM

ATM

Cisco

ONS 15454

203233

«
...
14
15
16
17
18
...
»

Содержание 3825 Series







































































































































































































































































































































































Отзывы:

Нет отзывов