Cisco 3825 Series Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 358

Cisco 3825 Series Скачать руководство пользователя страница 130

4-72

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Chapter 4 Configuring the Cisco 3825 Mobile Wireless Edge Router in a RAN-O Solution with the Command-Line

Monitoring and Managing the Cisco 3825 Router

show interface

type

slot

/

port

Displays the configuration and status of the
specified interface.

show interfaces fastethernet slot/port

Displays the status of the FE interface.

show interfaces gigabitethernet slot/port

Displays the status and configuration settings of
the GE interface.

show ip rtp header-compression

Displays RTP header compression statistics.

show l2tp session

Displays session information about active Layer 2
sessions.

show l2tp tunnel

Displays information about active Layer 2
tunnels.

show mpls l2transport vc

Displays information about Any Transport over
MPLS (AToM) virtual circuits (VCs) that have
been enabled to route Layer 2 packets on a router.

show network-clocks

Displays the network clocking configuration.

show ppp multilink

Displays MLP and multilink bundle information.

show ppp multilink interface

number

Displays multilink information for the specified
interface.

show protocols

Displays the protocols configured for the router
and the individual interfaces.

show redundancy

Displays current redundant setting and recent
changes in state.

show standby

Displays HSRP configuration information.

show umts traffic

Displays traffic rates, in bits per second, at 1
second, 5 seconds, 1 minute, 5 minutes, and 1 hour
intervals for UMTS data transmitted and received
over the backhaul.

show umts congestion atm

Displays the UMTS Congestion state.

show umts-iub efficiency

Displays the history of the UMTS Iub interface
efficiency averages for
compression/decompression at 1-second,
5-second, 1-minute, 5-minute, and 1-hour
intervals.

show umts-iub errors

Displays error statistics UMTS-Iub interface.

show umts-iub packets

Displays packet statistics of the UMTS-Iub
interface.

show umts-iub peering

Displays peering status, statistics, and history of
the UMTS Iub interface.

show umts-iub pvc

Displays the pvc mapping of the UMTS Iub
interface

show xconnect all

Displays xconnect information.

Command

Purpose

«
...
128
129
130
131
132
...
»

Содержание 3825 Series







































































































































































































































































































































































Отзывы:

Нет отзывов