Cisco 3825 Series Скачать руководство пользователя страница 106

Страница: 106 / 358

4-48

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Chapter 4 Configuring the Cisco 3825 Mobile Wireless Edge Router in a RAN-O Solution with the Command-Line

Configuration Sequence

For example, the following command specifies the class as the llq-class.

Router(config-pmap)#

class llq-class

When you enter the

class

command, you are in the class submode of the policy-map configuration mode.

Step 3

Allocate a percentage of bandwidth to be used for the prority queue.

Router(config-pmap-c)#

priority

percent

number

For example, the following command specifies a

priority percent

number of 99.

Router(config-pmap-c)#

priority percent 99

Step 4

Associate the llq-policy with a default class map. The default class is used for non-priority traffic.

Router(config-pmap-c)#

class

class

default

Step 5

Allocate the remaining bandwidth to the default class.

Router(config-pmap-c)#

bandwitdh

remaining

percent

number

For example, the following command specifies the remaining bandwidth as 1 percent.

Router(config-pmap-c)#

bandwidth remaining percent 1

Step 6

Limit the queue depth of the default queue.

Router(config-pmap-c)#

queue-limit

number

For example, the following command limits the queue depth to 45.

Router(config-pmap-c)#

queue-limit 45

Note

The queue limit on the default class should be less than the hold-queue specified on the multilink
interface.

Step 7

Exit the class map and policy map configuration modes.

Router(config-pmap-c)#

exit

Router(config-pmap)#

exit

For more information about these commands, see the

Cisco IOS Quality of Service Solutions Command

Reference

for your Cisco IOS Release.

Specify the Location of the Interface

Step 1

Enter interface configuration mode and specify the location of the interface.

Router(config)#

interface atm

slot

/subslot/

port

For example, the following command specifies the location of the interface as ATM0/0.

Router(config#

interface atm0/0/0

Step 2

Disable the IP address configuration for the physical layer interface.

Router(config-if)#

no ip address

Содержание 3825 Series







































































































































































































































































































































































Результаты поиска

Содержание 3825 Series

Отзывы:

Cisco 3825 Series, Руководство по настройке программного обеспечения, Страница: 106 / 358

Результаты поиска

Содержание 3825 Series

Отзывы: