Cisco 3825 Series Скачать руководство пользователя страница 140

Страница: 140 / 358

A-8

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

backup peer

To specify a redundant peer for a PW VC, use the

backup peer

command in the interface configuration

mode or xconnect configuration mode. To remove the redundant peer, use the

form of this command.

backup peer

peer-router-ip-addr vcid

[

pw-class

pw-class-name

]

no backup peer

peer-router-ip-addr vcid

Syntax Description

Defaults

No redundant peer is established.

Command Modes

Interface configuration

Xconnect configuration

Command History

Usage Guidelines

The combination of the

peer-router-ip-addr

and

vcid

arguments must be unique on the router.

Examples

The following example shows an MPLS xconnect with one redundant peer:

Router#

config t

Router(config)#

pseudowire-class mpl

Router(config-pw-class)#

encapsulation mpls

Router(config-pw-class)#

exit

Router(config)#

interface atm1/0/0

Router(config-if)# xconnect

10.0.0.1 100 pw-class mpls

Router(config-if-xconn)#

backup peer 10.0.0.2 200

Router(config-if-xconn)#

exit

Router(config-if)#

exit

Router(config)#

exit

peer-router-ip-

addr

IP address of the remote peer.

vcid

The 32-bit identifier of the VC between the routers at each end of the layer control
channel.

pw-class

(Optional) PW type. If not specified, the PW type is inherited from the parent
xconnect.

pw-class-name

(Optional) Name of the PW you created when you established the PW class.

Release

Modification

12.0(31)S

This command was introduced.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.4(11)T

This command was integrated into Cisco IOS Release 12.4(11)T.

12.2(33)SRB

This command was integrated into Cisco IOS Release 12.2(33)SRB.

12.4(16)MR

This command was integrated into Cisco IOS Release 12.4(16)MR.

Содержание 3825 Series







































































































































































































































































































































































Результаты поиска

Содержание 3825 Series

Отзывы:

Cisco 3825 Series, Руководство по настройке программного обеспечения, Страница: 140 / 358

Результаты поиска

Содержание 3825 Series

Отзывы: