Cisco 3700 series Скачать руководство пользователя

Страница: 67 / 114

3-21

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Chapter 3 Installing the Router

Connecting WAN, LAN, and Voice Cables

Connection Procedures and Precautions

Connect each WAN, LAN, and voice cable to the appropriate connector on the chassis or on a network
module or interface card.

•

Position the cables carefully, so that they do not put strain on the connectors.

•

Organize cables in bundles so that cables do not intertwine.

•

Inspect the cables to make sure that the routing and bend radiuses are satisfactory. Reposition cables,
if necessary.

Table 3-3

WAN, LAN, and Voice Connections

Port or Connection

Port type, color

Connection

Cable

Fast Ethernet

RJ-45, yellow,

Ethernet hub

Straight-through Ethernet

T1/E1 WAN

RJ-48C/CA81A,
blue

T1 or E1 network

RJ-48 T1/E1

Cisco serial

60-pin D-sub, blue

CSU/DSU and serial network or
equipment

Cisco serial transition cable that matches
the signaling protocol (EIA/TIA-232,
EIA/TIA-449, V.35, X.21, or
EIA/TIA-530) and the serial port
operating mode (DTE or DCE).

See the

Cisco Modular Access Router

Cable Specifications

document for

information about selecting these cables.

Cisco Smart Serial

Cisco Smart
compact connector,
blue

CSU/DSU and serial network or
equipment

For WIC-2T and WIC-2A/S only

DSL

DSL = digital subscriber line.

RJ-11C/CA11A,
lavender

Network demarcation device for
service provider’s DSL interface

RJ-11

T1/E1 digital voice

RJ-48C/CA81A,
tan

Digital PBX

RJ-48 T1/E1 cable

Analog voice FXS

FXS = foreign exchange station.

RJ-11, gray

Telephone, fax

RJ-11

Analog voice FXO

FXO = foreign exchange office.

RJ-11, pink

Central office, analog PBX

RJ-11

Analog voice E&M

E&M = ear and mouth.

RJ-11, brown

Analog PBX

RJ-11

BRI S/T WAN
(external NT1)

RJ-45/CB-1D,
orange

NT1 device or private integrated
network exchange (PINX)

RJ-45 straight-through

BRI U WAN
(built-in NT1)

RJ-49C/CA-A11,
red

ISDN network

RJ-48 straight-through

CT1/PRI

External T1 CSU

DB-15 T1 serial cable

CT1/PRI-CSU

RJ-48C/CA81A interface

RJ-48 straight-through

CE1/PRI

E1 network

DB-15 to BNC, DB-15 to DB-15, DB-15
to twinax, or DB-15 to RJ-45

56/64-kbps CSU/DSU 8-pin modular, blue RJ-48S interface

RJ-48 straight-through

Содержание 3700 series



















































































































Результаты поиска

Содержание 3700 series

Отзывы:

Похожие инструкции для 3700 series

Бренды по названию

Популярные бренды

Cisco 3700 series, Руководство по установке оборудования

Результаты поиска

Содержание 3700 series

Отзывы:

Похожие инструкции для 3700 series

Бренды по названию

Популярные бренды