Cisco 3700 series Скачать руководство пользователя | Manualshive

Страница: 78 / 114

background image

3-32

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Chapter 3 Installing the Router

Configuring the Router

Press RETURN to get started!

Step 12

The user prompt appears:

3700>

After you complete the initial configuration tasks, your Cisco router is ready to configure for specific
functions. For configuration procedures, see the

Software Configuration Guide for Cisco 2600 Series,

Cisco 3600 Series, and Cisco 3700 Series Routers

or the

Cisco IOS software configuration

documentation

. You can access these documents on Cisco.com.

Initial Configuration Using the CLI (Manual Configuration)

This section shows how to bring up a command-line interface (CLI) prompt for configuration using the
CLI, and it directs you to documentation for the CLI configuration.You can use the CLI if you see the
following messages at the end of the startup sequence:

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

Note

If these messages do not appear, SDM and a default configuration file have been installed on the router
at the factory. To use SDM to configure the router, see the quick start guide that shipped with your router.
You can also access the

Cisco 3700 series routers quick start guides

online at:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3700/37xx_qsg/index.htm

Note

To avoid losing work you have completed, be sure to save your configuration occasionally as you
proceed. Use the

copy running-config startup-config

command to save the configuration to NVRAM.

Step 1

To proceed with manual configuration using the CLI, enter

no

.

Would you like to enter the initial configuration dialog? [yes/no]:

no

Step 2

Press

Return

to terminate autoinstall and continue with manual configuration.

Would you like to terminate autoinstall? [yes]

Return

Several messages are displayed, ending with a line similar to the following:

...

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled <

date

> <

time

> by <

person

>

«
...
76
77
78
79
80
...
»

Содержание 3700 series



















































































































Отзывы:

Нет отзывов

Похожие инструкции для 3700 series

Бренд: Panasonic Страницы: 72

Touchstone MG2402G

Бренд: Arris Страницы: 8

Бренд: Lantronix Страницы: 2

Бренд: Yeastar Technology Страницы: 104

TTN Gateway v1 - EU

Бренд: The Things Network Страницы: 20

Бренд: Grandstream Networks Страницы: 20

Бренд: Microhard Systems Страницы: 186

Бренд: Ruckus Wireless Страницы: 2

Бренд: HD Страницы: 2

VoiceGATE 8D5499

Бренд: Digicom Страницы: 29

Бренд: National Instruments Страницы: 18

Бренд: Planet Страницы: 30

Бренд: Planet Networking & Communication Страницы: 38

VGW 20FS Series

Бренд: Planet Networking & Communication Страницы: 84

Hot Spot WSG-403

Бренд: Planet Networking & Communication Страницы: 125

Бренд: ELKOR Страницы: 2

Бренд: ActionTec Страницы: 41

OfficeConnect 3C100XF

Бренд: 3Com Страницы: 260

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды