Cisco 3700 series страница 75 Скачать руководство пользователя | Manualshive

Страница: 75 / 114

background image

3-29

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Chapter 3 Installing the Router

Configuring the Router

Note

If the

rommon 1>

prompt appears, your system has booted in ROM monitor mode. For information on the

ROM monitor, see the router rebooting and ROM monitor information in the

Cisco IOS Configuration

Fundamentals Configuration Guide

for your Cisco IOS software release.

Configuring the Router

You can configure your router by using one of the following tools:

•

Security Device Manager. If your router was purchased with a VPN bundle, Security Device
Manager is installed on the router. See the

“Initial Configuration Using SDM” section on page 3-29

.

•

Setup command facility. You can use the setup command facility to prompt you for basic router
information. After the configuration file has been created, you can use the CLI or use Security
Device Manager to perform additional configuration. See the

“Initial Configuration Using the Setup

Command Facility” section on page 3-29

.

•

Command-line interface (CLI). If you prefer to use the Cisco IOS CLI, see the

“Initial Configuration

Using the CLI (Manual Configuration)” section on page 3-32

for instructions on how to use the CLI.

Note

If you need help with interface and port numbering, see the

“Interface Numbering” section on page 1-5

.

Initial Configuration Using SDM

If Security Device Manager has been installed on your router, the following messages appear at the end
of the startup sequence:

yourname con0 is now available

Press RETURN to get started.

For configuration procedures using SDM, see the quick start guide that shipped with your router.

You can also access the

Cisco 3700 series routers quick start guides

online at:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3700/37xx_qsg/index.htm

Initial Configuration Using the Setup Command Facility

This section shows how to use the setup command facility to configure a host name for the router, set
passwords, and configure an interface for communication with the management network. If you see the
following messages at the end of the startup sequence, the setup command facility has been invoked
automatically:

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

«
...
73
74
75
76
77
...
»

Содержание 3700 series



















































































































Отзывы:

Нет отзывов

Похожие инструкции для 3700 series

Бренд: AMPLIFIED ENGINEERING Страницы: 20

Бренд: 3onedata Страницы: 4

ARG600 Single SIM Variant

Бренд: ABB Страницы: 64

BlueBeacon Gateway D

Бренд: BlueUp Страницы: 28

DIRIS Digiware M-50

Бренд: socomec Страницы: 60

Бренд: DAVIS Страницы: 8

Бренд: MIKRODEV Страницы: 12

Бренд: intwine connect Страницы: 8

SMART/RG SR555ac

Бренд: ADTRAN Страницы: 154

Бренд: UNION Market Страницы: 36

Бренд: Dormakaba Страницы: 8

XMG3927-B 0A Series

Бренд: ZyXEL Communications Страницы: 2

Бренд: Watchguard Страницы: 18

Бренд: SAGEMCOM Страницы: 29

Бренд: ViewSonic Страницы: 6

Бренд: RTA Страницы: 66

Airspot DSA-3100

Бренд: D-Link Страницы: 79

AC-4CM10-640-F-20-000

Бренд: Janus Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды