Cisco 3700 series страница 91 Скачать руководство пользователя | Manualshive

Страница: 91 / 114

background image

A-11

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Appendix A Troubleshooting

Error Messages

System

PS1, PS2,
LED on
power
supply rear
panel

Amber

Amber

Error:

%PS-3-MULTFAIL: There is more than one failure with the Power System #; please

resolve problems immediately.

Explanation:

The specified power supply (1 or 2) has experienced multiple failures. This is a critical
condition that must be resolved immediately.

Recovery:

1.

Check the power supply LEDs to identify the faulty unit.

2.

Power down the faulty power supply and circuit breaker (for a DC power supply).

3.

Check that cables are seated properly and terminal blocks are wired correctly.

4.

Power up the circuit breaker (for a DC power supply) and the power supply.

5.

If the error condition persists, replace the power supply. See the instructions that ship with
the new power supply.)

When the error condition is resolved, the following informational message appears:

%PS-3-PSOK: Power System is now normal.

—

—

Error:

%FAN-3-FAN_FAILED: Fan # had a rotation error reported.

Explanation:

The specified fan is not rotating at the desired speed.

Recovery:

Replace the fan cage as described in the

Installing Field-Replaceable Units in Cisco 3745

Routers

hardware configuration note.

When the error condition is resolved, the following informational message appears:

%FAN-3-FAN_OK: Fan # had earlier reported a rotation error. It is ok now.

—

—

Error:

%OIR-6-REMCARD: Card removed from slot x, interfaces disabled.

Explanation:

The online insertion and removal (OIR) function detected the removal of a network module
processor from the specified chassis slot. The interfaces on that processor are administratively
shut down and removed. In addition, the routing table is flushed of any routes through the
removed interfaces.

For more information, see the online

Cisco Network Modules Hardware Installation Guide

.

This is an informational message that does not require any recovery procedure.

Table A-5

System Error and Recovery Messages (continued)

LED Type

LED Color

Message

«
...
89
90
91
92
93
...
»

Содержание 3700 series



















































































































Отзывы:

Нет отзывов

Похожие инструкции для 3700 series

Бренд: ICP DAS USA Страницы: 8

SmartZone EPA126

Бренд: Panduit Страницы: 13

Бренд: CYP Страницы: 12

Бренд: IntesisBox Страницы: 63

Бренд: Veratron Страницы: 79

Бренд: McQuay Страницы: 52

Mobile Gateway 3.0

Бренд: SmartKitchen Страницы: 4

Бренд: WePresent Страницы: 8

Бренд: MediaAccess Страницы: 68

Бренд: SAGEMCOM Страницы: 60

Бренд: Profibus Страницы: 42

Бренд: Bpt Страницы: 25

Fieldgate SFG500

Бренд: Endress+Hauser Страницы: 52

Бренд: Planet Networking & Communication Страницы: 2

Бренд: TECOM Страницы: 49

Бренд: Black Box Страницы: 9

Бренд: Black Box Страницы: 32

Бренд: ActionTec Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды