Cisco 3700 series Скачать руководство пользователя | Manualshive

Страница: 106 / 114

background image

C-4

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Appendix C Configuration Register

Configuring the Boot Field

The boot field specifies a number in binary form. If you set the boot field value to 0, you must have
console port access to boot the operating system manually. See the

boot

command in the

“ROM Monitor

Command Descriptions” section on page B-3

.

If you set the boot field to a value of 2 to F, and a valid

boot system

command is stored in the

configuration file, the router software processes each

boot

command in sequence until the process is

successful or the end of the list is reached. If no

boot

commands are in the configuration file, the router

attempts to boot the first file in CompactFlash memory.

In the following example, the configuration register is set to boot the router automatically from
CompactFlash memory and to ignore Break at the next reboot of the router:

Router#

configure terminal

Enter configuration commands, one per line.

Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Z

config-register 0x102

Ctrl-z

Router#

Note

A

boot system

command in the router configuration in NVRAM overrides booting from CompactFlash

memory.

Bit 8 controls the console Break key. Setting bit 8 (the factory default) causes the processor to ignore the
console Break key. Clearing bit 8 causes the processor to interpret Break as a command to force the
router into the bootstrap monitor, halting normal operation. Break can always be sent in the first
60 seconds while the router is rebooting, regardless of the configuration settings.

Bit 9 controls the system boot. Clearing bit 9 (the factory default) causes the system to boot from
CompactFlash memory. Clearing bit 9 causes the system to use the secondary bootstrap. This bit is
typically not used.

Bit 10 controls the host portion of the IP broadcast address. Setting bit 10 causes the processor to use all
zeros; clearing bit 10 (the factory default) causes the processor to use all ones. Bit 10 interacts with
bit 14, which controls the network and subnet portions of the broadcast address.

Table C-3

shows the

combined effect of bits 10 and 14.

Bit 13 determines how the router responds to a bootload failure. Setting bit 13 causes the router to load
operating software from ROM after six unsuccessful attempts to load a boot file. Clearing bit 13 causes
the router to continue indefinitely to attempt loading a boot file. By factory default, bit 13 is set to 0.

Bits 5, 11, and 12 of the configuration register determine the data rate of the console terminal.

Table C-4

shows the bit settings for the eight available rates. (The default data rate is 9600 bps.)

Table C-3

Configuration Register Settings for Broadcast Address Destination

Bit 10

Bit 14

Address (<net> <host>)

Off

Off

<ones> <ones>

On

Off

<zeros> <zeros>

On

On

<net> <zeros>

Off

On <net>

<ones>

«
...
104
105
106
107
108
...
»

Содержание 3700 series



















































































































Отзывы:

Нет отзывов

Похожие инструкции для 3700 series

Бренд: GE Страницы: 3

Бренд: GE Страницы: 124

Бренд: Banner Страницы: 96

Бренд: Yeastar Technology Страницы: 11

Бренд: ZyXEL Communications Страницы: 210

Бренд: Spectrum Brands Страницы: 2

Бренд: Nitgen Страницы: 66

NetVanta 6330 Series

Бренд: ADTRAN Страницы: 4

Бренд: VOGO Страницы: 24

Бренд: Toro Страницы: 40

LAN ECO Comfort

Бренд: SiKom Страницы: 2

NIOT-E-TIB100-GB-RE

Бренд: hilscher Страницы: 263

UNIGATE EL-DeviceNet

Бренд: DEUTSCHMANN AUTOMATION Страницы: 62

UNIGATE CM - PROFIBUS

Бренд: DEUTSCHMANN AUTOMATION Страницы: 62

Бренд: Dynamix Страницы: 122

Бренд: Zhone Страницы: 151

Бренд: Primus Страницы: 2

Бренд: enphase Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды