CIMCO OXE Diesel 125 HP Скачать руководство пользователя страница 47

Страница: 47 / 84

OXE 125/150/175/200 HP INSTALLATION MANUAL

INSTALLATION WIRING

IDENTIFICATION OF WIRING HARNESS GENERATIONS

NOTE!

The decal G4 indicates that the OXE outboard is equipped with engine

harness G4 or later. No decal indicates engine harness 3.5

WARNING

G4 engine harness may be used in combination with helm harness 3.5.

It is NOT possible to use the G3.5 engine harness in combitaion with G4 helm
harness. The G3.5 engine harness can function with G3.5 helm harness only!

WARNING

When installing the helm harness built for the OXE-diesel it is important not
to connect any peripheral devices to the OXE Diesel Engine CAN system.

NOTE!

Any peripheral equipment should be connected to the separate

CAN system (user NMEA system).

NOTE!

Connecting any peripheral equipment to the helm harness (OXE Internal

CAN) will void the warranty.

Содержание OXE Diesel 125 HP





















































































Результаты поиска

Содержание OXE Diesel 125 HP

Отзывы:

Похожие инструкции для OXE Diesel 125 HP

Бренды по названию

Популярные бренды

CIMCO OXE Diesel 125 HP, Руководство по установке

Результаты поиска

Содержание OXE Diesel 125 HP

Отзывы:

Похожие инструкции для OXE Diesel 125 HP

Бренды по названию

Популярные бренды