Christie DHD630-GS Скачать руководство пользователя страница 58

Страница: 58 / 79

Ventilation and cooling

GS Series 630-635 Service Manual

020-001224-02 Rev. 1 (08-2018)

See

Removing the top cover

on page 51,

Removing the rear cover

on page 52, and

Removing

the left-side cover

on page 53.

2. Remove the main board and I/O board.

See

Replacing the main board and I/O board

on page 69.

3. Remove fans 4 and 5.

See

Replacing fans 4 and 5

on page 58.

4. Remove the complete light engine.

See

Replacing the complete light engine

on page 66.

5. To replace fan 3, remove the four M3 screws with a Phillips #1 screwdriver securing the fan.

6. Remove the harnesses from the clips.

7. Replace the affected fan.

8. To re-install, follow these steps in reverse order.

Replacing fans 4 and 5

The fans 4 and 5 draw the air into the projector and provides exhaust cooling for the front laser driver
bank and rear laser driver bank.

1. Remove the top cover.

See

Removing the top cover

on page 51.

2. Remove the rear IR board.

See

Replacing the rear IR

board

on page 68.

Содержание DHD630-GS
















































































Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды

Christie DHD630-GS, Руководство по обслуживанию

Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды