Christie DHD630-GS Скачать руководство пользователя страница 28

Страница: 28 / 79

Service setups

GS Series 630-635 Service Manual

020-001224-02 Rev. 1 (08-2018)

1. Write down the projector IP.

a. Plug in the power cord to the projector.

b. Connect the PC and projector using a RJ45 cable.

c. Turn on the projector.

d. On the IR remote keypad, select Menu > Configuration > Communications >

LAN.

e. Make sure DHCP is disabled.

f. Write down the following information:

• The IP address: 192.168.0.100 (default)

• The Subnet Mask: 255.255.255.0 (default)

2. In Network settings, set the projector IP address.

See

Performing a network function test on the network port

on page 26.

3. Read the projector information.

See

Performing a network function test on the network port

on page 26.

Performing a RS232 and video function test on
HDBaseT port

To perform the RS232 and video function test, complete the following steps.

1. Connect the CH-506TX, projector and PC as shown in step 5.

2. Select the signal source HDBaseT.

3. On the IR remote keypad, press Menu > Configuration > Communications> Serial port >

HDBaseT.

4. Set the PC Baud Rate to 115200.

5. Input the RS232 command (SYS?).

The projector returns (SYSx).

RJ45 to HDBaseT port

RS232 to PC

Power

HDMI input

Содержание DHD630-GS
















































































Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды

Christie DHD630-GS, Руководство по обслуживанию

Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды