Christie DHD630-GS Скачать руководство пользователя страница 17

Страница: 17 / 79

Service setups

GS Series 630-635 Service Manual

020-001224-02 Rev. 1 (08-2018)

7. After completing the adjustment, tighten the screw (indicated by the arrows in the image

below).

8. To lock the screw, use Loctite 222 or green glue (BONBOND LOCK BB-2100).

Calibrating

the lens

Always perform a lens calibration after repairing the main board or replacing the light engine.

1. Place the projector on a clean horizontal surface.

2. On the IR remote or keypad, press Menu > Options > Lens Setting.

3. Select Lens Calibration.

4. Press Enter.

Adjusting the ROD assembly

Avoid over-adjusting the ROD to prevent damage.

1. Remove the top cover.

See

Removing the top cover

on page 51.

2. To power on with the top cover removed, firmly hold the interlock switch on the left-side cover.

Warning! Failure to comply with the following could result in death or serious injury.

• Do not look into the projector lens when the laser is on. The extremely high brightness can cause

permanent eye damage.

Part name

Description

Inspection item

Check if the lens shift is moving smoothly.

Criteria

The lens shift is moving smoothly.

Warning! Failure to comply with the following could result in death or serious injury.

• This projector has built-in Class 4 laser module. Never attempt to operate the projector without all

covers properly installed unless instructed to do so in this manual for service.

• Do not look into the projector lens when the laser is on. The extremely high brightness can cause

permanent eye damage.

The screw

ABC adjustment bar

Содержание DHD630-GS
















































































Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды

Christie DHD630-GS, Руководство по обслуживанию

Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды