Christie DHD630-GS Скачать руководство пользователя страница 16

Страница: 16 / 79

Service setups

GS Series 630-635 Service Manual

020-001224-02 Rev. 1 (08-2018)

Performing an auto-brightness constant
calibration

Always perform an auto-brightness constant (ABC) calibration after repairing the main board, the
cooling module, or replacing the light engine.

1. Remove the top cover before during the adjustment.

See

Removing the top cover

on page 51.

2. To power on with the top cover removed, firmly hold the interlock switch on the left cover.

3. Enter Factory mode.

See

Entering Factory mode

on page 13.

4. Select LD Menu.

5. To confirm whether the value of LS (light sensor) is within specification, refer to the image

below.

• DHD635-GS

DWU635-GS

DHD630-GS and DWU630-GS: 3000 to 4000 kHz

6. If the value is out of specification, adjust the ABC adjustment bar (indicated by the arrows in

the image in step 8) with a Phillips #1 screwdriver, until the value is within specification.

Warning! Failure to comply with the following could result in death or serious injury.

• This projector has built-in Class 4 laser module. Never attempt to operate the projector without all

covers properly installed unless instructed to do so in this manual for service.

• Do not look into the projector lens when the laser is on. The extremely high brightness can cause

permanent eye damage.

The value

Содержание DHD630-GS
















































































Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды

Christie DHD630-GS, Руководство по обслуживанию

Результаты поиска

Содержание DHD630-GS

Отзывы:

Похожие инструкции для DHD630-GS

Бренды по названию

Популярные бренды