Christie CP42LH Скачать руководство пользователя страница 60

Страница: 60 / 90

Parts and Module Replacement

CP42LH Service Manual

020-101686-03 Rev. 1 (08-2016)

8. Wearing the gloves provided with the service kit, pull the integrator assembly toward the lens

element and lift it up and out of the projector.

9. Set the integrator assembly in a clean area where it cannot be damaged.

10. Recreate your Measured Color Gamut Data (MCGD) files. See the user manual for instructions.

Fold mirror access panel

The fold mirror access panel is located underneath the front section of the projector.
Estimated replacement time: 15 m 30 minutes for calibration

1. Open the

Optical access door

, see page 43.

2. Disconnect the P14 connector.

3. Pull the harness through the cable retaining clips to allow movement of the harness.

4. Remove the screw securing the retaining clip.

5. Remove the 4 screws securing the fold mirror access panel.

6. Disconnect the color sensor connector.

7. Remove the fold mirror access panel.

Cold mirror

The cold mirror is located close to the integrator assembly.
Estimated replacement time: 20 m 30 minutes for calibration

1. Remove the

Front top lid

, see page 41.

2. Remove the 2 screws securing the infrared emitter housing.

3. Remove and set aside the infrared emitter housing.

4. Remove one of the screws from each of the 3 clips securing the cold mirror.

When reinstalling the integrator assembly, adjust the integrator/fold mirror for

proper aperture alignment. See

Align the fold mirror

Wear clean lint-free cotton gloves when handling the cold mirror and handle by the edges

only. Fingerprints left on the surface can negatively impact a displayed image.

Содержание CP42LH



























































































Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды

Christie CP42LH, Руководство по обслуживанию

Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды