Christie CP42LH Скачать руководство пользователя

Страница: 53 / 90

Parts and Module Replacement

CP42LH Service Manual

020-101686-03 Rev. 1 (08-2016)

6. Push down the lever in the light engine compartment.

7. Pull the fan pack assembly out of the projector.

Light engine fans (fans 1, 2, 3, and 4)

Estimated replacement time: 10 minutes per fan

1. Remove the

Fan pack assembly

, see page 52.

2. Disconnect the inline connector for the defective fan.

3. Release the harness from the routing clips.

4. Remove the fan and the rubber isolators.

Red FPGA fan (fan 5)

Estimated replacement time: 9.5 minutes

1. Remove the

Fan pack assembly

, see page 52.

2. Disconnect the fan #5 inline connector from underneath.

Do not operate the projector with the light engine fan pack or light engine removed. This

causes overheating of the SFB FPGAs. Failure to comply may result in equipment damage.

Install the fan with the directional arrow facing into the projector.

Содержание CP42LH



























































































Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды

Christie CP42LH, Руководство по обслуживанию

Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды