Christie CP42LH Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 90

background image

Safety Information

CP42LH Service Manual

24

020-101686-03 Rev. 1 (08-2016)

AC/power precautions

Lead dress

Before servicing, always carefully observe the original lead dress. Take extra precautions to secure
all harnessing properly, especially in high voltage circuitry areas. Replace any wires with damaged
insulation.

Test the interlocks

Once the projector is running, ensure the safety interlocks are functioning.

Test the key switch

1. Turn the key switch on the laser rack off.

2. Check the status lights on the back of the projector are off.

3. Turn on the key switch.

4. Press Manual Reset on the projector.

Test the laser rack emergency stop

1. Press the emergency stop button on the laser rack.

Failure to comply with the following could result in death or serious injury.

• Use only the AC power cord provided with the projector. Do not attempt operation if the

AC supply is not within the specified voltage and power range, as specified on the license
label.

• As a safety feature the projector is equipped with a three-wire plug with a third

(grounding) pin. If you cannot insert the plug into the outlet, contact an electrician to
have the outlet replaced. Do not defeat the safety purpose of the grounding-type plug.

• Loose cables provide a trip or fire hazard. Position all cables where they cannot contact

hot surfaces, be pulled, or be tripped over.

• Damaged cables provide a fire hazard. Do not allow anything to rest on the power cord.

Never operate the projector if a cable appears damaged.

• Overloaded power outlets and extension cords provide a fire and shock hazard. Do not

overload power outlets or extension cords.

• Disconnect projector from AC before opening any enclosure.

Only qualified service technicians are permitted to open projector enclosures and only if the
projector is disconnected from AC power. Failure to comply could result in minor or moderate
injury.

Before displaying an image from the projector, test the three interlock devices. Every time

the interlock is activated, the laser modules turn off. Failure to comply could result in death

or serious injury.

«
...
22
23
24
25
26
...
»

Содержание CP42LH



























































































Отзывы:

Нет отзывов

Похожие инструкции для CP42LH

NP41 - TECHNISCHE DATEN

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 44

Бренд: NEC Страницы: 16

Nighthawk XT4100

Бренд: NEC Страницы: 11

Бренд: NEC Страницы: 3

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 151

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 3

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 17

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды