Christie CP42LH Скачать руководство пользователя страница 55

Страница: 55 / 90

Parts and Module Replacement

CP42LH Service Manual

020-101686-03 Rev. 1 (08-2016)

2. Remove the

Light engine lid

, see page 42.

3. Disconnect the inline connector and release the harness from the routing clip.

4. Remove the 4 screws securing each fan.

5. Remove the fan from the rubber isolators.

IOS fan (fan 14)

Estimated replacement time: 6.5 minutes

The IOS fan provides air cooling to the optical compartment.

1. Remove the

2. Remove the

3. Remove the

4. Pull the IOS fan from the 4 rubber mounts.

5. Remove the fan from the fan bracket.

6. Disconnect the harness from the routing clip.

7. Remove the fan.

Blue/Green LAD fan (fan 15)

Estimated replacement time: 13 minutes

1. Remove the

2. Remove the

3. Loosen the 2 screws securing the LAD fan assembly to the light engine assembly.

4. Disconnect the LAD fan harness from the inline connector and cut the cable tie to release the

harness.

5. Remove the fan.

Radiator Fans (fans 16, 17, 18, and 19)

Estimated replacement time: 16.5 minutes per fan

The radiator fans provide air cooling to the liquid cooling radiator.

1. Remove the

Liquid cooling assembly

, see page 56.

2. Remove the 4 screws to release each fan.

Red LAD fan (fan 20)

1. Remove the

2. Remove the

Содержание CP42LH



























































































Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды

Christie CP42LH, Руководство по обслуживанию

Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды