CHP DPF-300 Скачать руководство пользователя страница 17

                                DPF-300    

                  

INSTRUCTION MANUAL

 

 

Page 17 

 

                           2020.09 

   

7. ENVIROMENTAL IMPACT 

 
 

The environmental impact of DPF-300 is minimal and has the following main characteristics: 

 

Dust pollution:  

the machine produces cutting dust that is collected by a special filter 

provided with a special filter cartridge. 

 

Oil pollution:  

                        

the machine does not use and, therefore, does not release oil into the 

           environment. 

 

 

Noise pollution:

 

the  machine  is  equipped  with  a  motor  spindle  that  may  generate 

noise  up  to  80  dB(A)  during  cutting,  measured  at  the  operator 
position.  The  machine  is  equipped  with  a  suction  turbine  that 

generates  noise  up  to  70  dB(A),  especially  its  rear  side  (that  is 
equipped with a silencer), measured at the operator position.  

 

 

Heat pollution: 

the machine features a suction turbine located inside the frame, which 

generates  hot  exhaust  air  that  comes  out  through  the  back  of  the 
turbine  (equipped  with  a  silencer);  also,  the  turbine  surfaces  are 
subject to overheating and may reach temperatures of up to 55°C.  

 
 

 
 

 
 
 

 

 

 

 
 

 
 

 
 
 

 
 

 
 
 

 
 

 
 

 
 
 

 
 

 
 
 

 

Содержание DPF-300



























Отзывы: