manualshive.com logo in svg

Chip Hyde VISION 3D, Инструкция по эксплуатации, Страница: 7 / 38

Поделиться
Скачать
Chip Hyde VISION 3D Скачать руководство пользователя страница 7

5. 

Items Needed to Complete the Vision 3D 

 

5.1  Components and Hardware Needed to Complete the 

Vision 3D 

 

Qty Description 

 

1 
 

50cc Motor and Propeller 

1 
 

3-1/2 inch ultimate Truturn spinner 

1 
 

16-24oz fuel tank 

2 
 

3-1/2 inch main wheels 

2 
 

4 & ¼ inch 4-40 thread elevator pushrods 

2 
 
 

4 & ¼ inch 4-40 thread in-board aileron servo pushrods 

WHEN USING ONE 

SERVO PER AILERON

 

4 

4 & ¼ inch 4-40 thread in-board aileron servo pushrods 

WHEN USING TWO 

SERVOS PER AILERON 

 

1 
 

Bag of 4-40 lock nuts for all linkages 

6 
 

4-40 pin clevises 

6 
 

4-40 ball-links 

2 
  

Aileron servos (130 oz inch)

 WHEN USING ONE SERVO PER AILERON 

4 
 

Aileron servos (60 oz inch)

 WHEN USING TWO SERVOS PER AILERON 

1 
 

Rudder servo (200 oz inch) 

2 
 

Elevator servos (130 oz inch) 

1 
 

Throttle Servo 

Extension 
Leads 

• 

2 x for in-board aileron servos (approx. 16 - 20 inches in length) 

• 

2 x for out-board aileron servos (approx. 40 – inches in length) 

WHEN 

USING TWO SERVOS PER AILERON

 

• 

2 x for elevator servos (approx. 28 inches in length) 

• 

1 x for rudder servo (approx. 28 inches in length) 

• 

2 x for permanent connection to Rx aileron connectors (short)  

 

1 
 

Receiver  

1 
 

Receiver switch (heavy duty) 

1 
 

Receiver battery (2000 mAh minimum) 

Содержание VISION 3D







































Отзывы:

Нет отзывов