Chip Hyde VISION 3D Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 38

Chip Hyde VISION 3D Скачать руководство пользователя страница 13

Remove the servo and add a few drops of thin CA into each hole.

Finally re-fit the servo and screw it into place. Cover over the unused
mounting position for the optional second aileron servo.

7.3

Aileron Linkage Installation

IMPORTANT

THIS SECTION WILL EXPLAIN THE AILERON LINAKGE
INSTALLATION. AS PART OF THIS YOU WILL INSTALL THE BALL
BEARING CONTROL HONRNS AND ACCOMPANYING METAIL
PINNED CLEVISES.

DO NOT TRY TO INSTALL THE CLEVIS INTO THE BALL BEARING
CONTROL HORNS BUY SPREADING THE CLEVIS WITH A FLAT TIP
SCREW DRIVER, THAT IS NOT THE WAY THEY ARE DESIGNED TO
WORK.

UNSCREW THE PHILLIPS HEAD SCREW PIN AND REMOVE IT
COMPLETELY FROM THE CLEVIS ITSELF. THEN SLIP THE HORN
TROUGH THE EMPTY SLOT AND REINSTALLL THE SCREW IN THE
CLEVIS.

NOT FOLLOWING THESE INSTRUCTIONS CAN CAUSE THE PLASTIC
THE CLEVIS IS MADE FROM TO FATIGUE AND FAILURES IN THE
BALLBEARING FROM THE EXCESSIVE SIDE LOADS PUT ON THE
INNER RACE. THIS IS NOT THE TYPE OF LOADS THESE BEARINGS
ARE DESIGNED TO WITHSTAND.

WE RECOMMEND THE USE OF THE SUPPLIED CLEVIS ONLY AS
THEY WERE DESIGNED SPECIFICALLY FOR THIS HORN.

CHIP

«
...
11
12
13
14
15
...
»

Содержание VISION 3D







































Отзывы:

Нет отзывов