Chip Hyde VISION 3D Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 38

Chip Hyde VISION 3D Скачать руководство пользователя страница 24

11 Horizontal Stabilizers and Servos/linkages Installation

The Vision 3D has plug in horizontal Stabilizers that may be permanently
fitted or alternatively screwed into position, allowing them to be removed
aiding transportation and storage of the fuselage.

11.1

Elevator Servos Installation

Install the two elevator servos. First remove the covering material over their
mounting points, including rectangles of material under the rear servo
mounting points for the Lite-ply mounting plates.

Next glue the Lite-ply plates in place with medium CA and then drill and screw
the servos into position. Remember to fit the 28-inch extension leads and tape
or heat-shrink the connectors together.

Elevator servo
fitted in position
with mounting
plate

11.2 Fitting and Hinging the Elevators

Following the same steps used for the ailerons and the rudder, fit in place the
elevators to the horizontal stabilizer halves and then apply CA to the hinges.

«
...
22
23
24
25
26
...
»

Содержание VISION 3D







































Отзывы:

Нет отзывов