Chicco 08079159510000, Инструкция по эксплуатации

Страница: 23 / 176

23 22
use of car safety belts and aim to provide great-
er stability for the child car seat.
1. Place the child car seat onto the vehicle seat
with the backrest up against the vehicle seat
backrest (Fig. 15).
WARNING! Check that the vehicle headrest
does not interfere with the child seat headrest:
it must not push it forwards (Fig. 6). If this hap-
pens, remove the car seat headrest. Remember
to replace the vehicle headrest when the child
car seat is removed and a passenger uses the
seat.
2. Pull the lever (O), located under the inclina-
tion adjuster button (H), upwards. (Fig. 16)
3. While keeping the lever pulled, pull out the
rigid clasps (P) completely from the rear of
the backrest (Fig. 17).
4. Insert the two rigid clasps (P) into the cor-
responding ISOFIX anchorage points on the
car seat, located between the backrest and
the seat (Fig. 18).
WARNING!
Check that the two indicators (Q)
are green which means the system has been
installed correctly (Fig.19).
5. Push the child car seat firmly against the
backrest of the car seat (Fig. 20), pushing the
lever (O) to ensure maximum adherence of
the child car seat backrest against the car seat.
6. Sit the child inside with his back against
the child car seat backrest and follow the
instructions 3-4-5-6-7-8 provided in the pre-
vious chapter to install the car safety belts,
(Fitting the child car seat inside the vehicle
using safety belts and rigid FixPlus clasps and
placing the child inside) paying attention to
every single detail.
HOW TO POSITION SAFE PAD
SAFE PAD (S) can be positioned on both sides
of the Car Seat depending on which seat the
Car Seat is installed.
To move it to the desired side, release it from
the diagonal belt guide (B) on the side it is in-
stalled by pressing button (I) (Fig. 21). Move it
to the other side, inserting it in the dedicated
diagonal belt guide (Fig. 22).
The rigid FixPlus clasps are designed to improve
the levels of comfort and stability of the child car
seat. It is possible to use the Oasys FixPlus child
car seat without these optionals, if you encoun-
ter problems installing them in your car.
INSTALLING THE CHILD SEAT INSIDE THE
VEHICLE WITHOUT THE CHILD INSIDE
When the child is not travelling in the car, the
child car seat should be left secured by the ve-
hicle three-point safety belt, or stowed away in
the car boot. An unsecured child car seat may
be a source of danger for the other passengers
in the event of an accident or sudden braking.
HOW TO REMOVE THE CHILD FROM THE
CHILD CAR SEAT
Release the car belt buckle, accompanying the
belt as it retracts.
REMOVAL OF THE CHILD CAR SEAT
WARNING! Remove the child from the child car
seat before removing it.
1. Release the car safety belt.
2. Unthread the diagonal strap through the
guide, accompanying it as it retracts.
If the rigid clasps have been used to fasten the
car seat in place, they must now be released
from the anchor points:
1. Pull the two red buttons on the rigid clasp re-
lease system® towards you, release the clasps
from the corresponding Isofix anchor points
on the car seat ( Fig. 23) so that the indicator
is completely red.
2. Hold the lever up (O) as you push the rigid
clasps all the way into the base of the child
car seat, ( Fig. 24).
HOW TO REMOVE AND REINSTALL SAFE PAD
Oasys 23 FixPlus EVO is certified for use with
and without SAFE PAD (S).
To remove SAFE PAD take off the rear cover (Fig.
25), unhook SAFE PAD (S) (Fig. 26) and remove
SAFE PAD (Fig. 27). When carrying out this oper-
ation remember to correctly replace the elastic
band behind the backrest. (Fig.39)
To reinstall SAFE PAD carry out the above oper-
ations in reverse.
INSTALLING AND REMOVING THE CUP
HOLDER
The child car seat has 2 inserts, one on the
right and one on the left of the side of the seat
where you can fit the cup holder whenever
you like.
To install the cup holder:
1. Insert the cup holder into the relative guide
( Fig. 28).
2. Press the cup holder downwards until it
clicks into place ( Fig. 29).
WARNING!
Do not place glass containers or
hot liquids on the cup holder as they could
harm the child.
To remove it:
1. Press the lever on the back of the cup holder
and lift it upwards, out of the guide ( Fig. 30)
The cup holder guides are fitted with a spe-
cial device that makes sure it always remains
in a horizontal position.
To rotate and position the cup holder:
1. Press the lever on the back and rotate it to
the desired position
ADJUSTING THE HEIGHT OF THE BACK
REST
The height of the headrest can be adjusted to
10 different positions to adapt the child car seat
to the height of the child.
Make sure the child’s head is always well pro-
tected and the car diagonal safety belt is posi-
tioned properly on his shoulder.
When adjusting the height of the backrest,
check that the diagonal belt loop (B) is posi-
tioned at a maximum of 2 cm above the child’s
shoulder ( Fig. 31).
To make the adjustment:
1. Use one hand to press the child car seat
backrest height adjuster lever (L) located on
the back of the headrest ( Fig. 32)
2. Raise/lower the backrest to adapt it to the
height of the child’s shoulders ( Fig. 33)
3. Release the lever checking that it has clicked
into the desired position.
ADJUSTING THE WIDTH OF THE BACK
REST
The width of the backrest can be adjusted to
adapt the child car seat to suit the physique of
the child.
Use the backrest width regulator wheel (K) lo-
cated above the headrest, to adjust the width: