•
7/32”,
3/16”
and
5/32”
Allen
head
wrenches
•
Flat
blade
screwdriver
For
installing
umbrella
to
table
or
stand:
•
No.
2
Phillips
screwdriver
•
7/16”
wrench
or
adjustable
wrench
•
Proper
personnel
for
lifting
umbrella
– weight
is
approximately
80
lbs.
Tools
Required
ASSEMBLE
WITH
CARE!
Pangard II
Polyester
Powdercoat is
a
strong,
long
‐
lasting
finish.
To
protect
this
finish
during
assembly,
place
unwrapped
powdercoated parts
on
packaging
foam
or
other
non
‐
marring
surface.
Do
not
place
or
slide
powdercoated parts
on
concrete
or
other
hard
or
textured
surface
– this
will
damage
the
finish
causing
rust
to
occur.
Use
touch
‐
up
paint
on
any
gouges
in
the
finish
caused
by
assembly
tools.
Altair
WARNING:
SOLSTICE
UMBRELLA
MUST BE
USED
WITH
SURFACE
MOUNTED
OR
EMBEDDED
TABLE
OR
SURFACE
MOUNT
STAND.
NOTE:
If
specifying
a
Solstice
umbrella
with
Landscape
Forms’
Charlie
picnic
tables,
the
surface
mount
stand
must
also
be
specified.
For
all
other
Landscape
Forms
tables
or
picnic
tables,
the
umbrella
secures
to
the
table
and
no
stand
is
required.
The
hardware
for
securing
the
umbrella
to
the
table
or
stand
is
shipped
with
the
support.
See
separate
installation
guides
for
surface
mount
stand
or
table.
Storage:
It
is
recommended
to
leave
the
Solstice
unit
installed
all
year.
If
the
unit
must
be
stored,
remove
from
table
or
stand.
Replace
the
bolt
in
the
table
or
stand.
Loosen
top
cap
center
screw
and
remove
pole
from
canopy
assembly.
Replace
screw
in
top
of
pole.
Cygnus
Included
components
1x
‐
Top
cap
8x
‐
strut
8x
‐
panel
1x
– Strut
ring
Altair
Cygnus
1x
‐
Pole
1x
– 3/8
‐
16
x
1
‐
1/4”
screw
16x
– 5/16
‐
18
x
1”
screw
8x
– #10
‐
24
x
1
‐
1/4”
screw
8x
– end
cap
nut
PROCEDURE
FOR
INSTALLATION:
Note:
Do
not
fully
tighten
any
hardware
until
the
unit
is
completely
assembled
.
As
hardware
is
installed,
tighten
until
just
snug,
then
loosen
1/2
turn.
Once
unit
is
assembled,
all
hardware
can
be
fully
tightened.
Assemble
umbrella
on
a
non
‐
marring
surface.
Sufficient
overhead
clearance
must
be
available
before
you
begin.
Avoid
low
hanging
power
lines.
1.
Install
and
anchor
table
or
surface
mount
stand
according
to
installation
guides.
2.
Install
strut
ring
on
pole.
See
Fig.
1.
3.
Install
the
top
cap
with
the
3/8
‐
16
x
1
‐
1/4”
socket
button
head
cap
screw.
See
Fig.
2.
4.
Attach
two
struts
to
strut
ring.
See
Figs
3a
and
3b.
5.
Install
one
panel
between
the
two
struts.
Fit
holes
in
end
caps
over
alignment
pin
at
the
end
of
each
strut.
Bolt
to
top
ring.
See
Figs
4a,
4b
and
4c.
6.
Attach
next
strut,
working
in
a
counter
‐
clockwise
direction
when
looking
at
the
top
of
the
umbrella.
See
Fig
5.
7.
Install
next
panel
by
repeating
step
5.
Bolt
together
the
panel
end
caps
using
the
#10
‐
24
screw
and
end
cap
nut.
Leave
1/8”
gap
between
end
caps.
See
Fig.
6.
8.
Rotate
umbrella
so
that
second
installed
panel
is
in
the
6
o’clock
position.
See
Fig.
7.
9.
Repeat
until
all
panels
and
struts
are
installed.
If
it
is
difficult
to
connect
the
final
end
caps,
relieve
stress
by
adjusting
the
top
of
the
panel
connection.
Check
to
ensure
that
all
endcaps have
1/8”
gap.
10. Once
unit
is
fully
assembled,
tighten
all
hardware.
Do
not
overtighten.
Tighten
end
cap
hardware
first,
strut
ring
hardware
second,
top
ring
hardware
third
and
then
the
top
cap
center
screw.
11. Lift
assembled
umbrella
into
hole
in
table
or
surface
mount
stand,
taking
care
not
to
scratch
the
tabletop.
12. Turn
umbrella
to
align
holes
in
support
and
pole.
Insert
1/4
‐
20
bolt
through
holes
and
install
locknut.
This
hardware
is
shipped
with
the
table
support
or
surface
mount
stand.
The
surface
mount
stand
has
two
screws
and
locknuts.
Installation Guide
Solstice: Altair, Cygnus
Umbrella
www.landscapeforms.com Ph: 800.521.2546
Date: June 17, 2016
Page 1 of 2
