background image

Page 4

SKU 97906

For technical questions, please call 1-800-444-3353.

Wear ANSI-approved safety goggles, 

5. 

heavy-duty work gloves, and dust 

mask/respirator during set up.
Use only oil and fuel recommended 

6. 

in the “Specifications” section of this 

manual.

operating precautionS

1. 

carBon Monoxide 

hazard 

using an engine indoors 

can KiLL You in 

MinuteS. 

Engine exhaust contains carbon 

monoxide.  This is a poison you 

cannot see or smell. 

NEVER use inside a home or garage, 

EVEN IF doors and windows are 

open. 

Only use OUTSIDE and far away 

from windows, doors, and vents.
Keep children away from the equip-

2. 

ment, especially while it is operating.
Do not leave the equipment unat-

3. 

tended when it is running.  Turn off 

the equipment (and remove safety 

keys, if available) before leaving the 

work area.
Wear ANSI-approved safety goggles 

4. 

and hearing protection during use.

People with pacemakers should 

5. 

consult their physician(s) before 

use.  Electromagnetic fields in close 

proximity to a heart pacemaker could 

cause pacemaker  interference or 

pacemaker failure.  Caution is neces-

sary when near the engine’s magneto 

or recoil starter.
Use only accessories that are recom-

6. 

mended by Harbor Freight Tools for 

your model.  Accessories that may be 

suitable for one piece of equipment 

may become hazardous when used 

on another piece of equipment.
Do not operate in explosive atmo-

7. 

spheres, such as in the presence of 

flammable liquids, gases, or dust.  

Gasoline-powered engines may ignite 

the dust or fumes.
Stay alert, watch what you are doing 

8. 

and use common sense when operat-

ing this piece of equipment.  Do not 

use this piece of equipment while 

tired or under the influence of drugs, 

alcohol or medication.
Do not overreach.  Keep proper foot-

9. 

ing and balance at all times.  This en-

ables better control of the equipment 

in unexpected situations.
Dress properly.  Do not wear loose 

10. 

clothing or jewelry.  Keep hair, cloth-

ing and gloves away from moving 

parts.  Loose clothes, jewelry or long 

hair can be caught in moving parts.
Parts, especially exhaust system 

11. 

components, get very hot during use.  

Stay clear of hot parts.
Do not cover the engine or equipment 

12. 

during operation.

Содержание 97906

























Отзывы: