background image

Page 16

SKU 97906

For technical questions, please call 1-800-444-3353.

after initial 20 operation hour period:

Change engine oil.

a. 

every 25 operation hours thereafter:

Clean/replace air filter element.

a. 

Inspect/clean spark plug.

b. 

every 50 operation hours:

Change engine oil.

a. 

Replace fuel filter (if equipped).

b. 

every 100 operation hours:

Replace spark plug.

a. 

Replace air filter element.

b. 

note:

  All maintenance procedures sched-

uled for 25, 50, and 100 operation 

hours should be performed at least 

yearly.

every 300 operation hours:

Clean fuel tank and carburetor.

a. 

Clean carbon build-up from combus-

b. 

tion chamber.

Storage

Wait for engine to cool, then clean 

1. 

engine with clean cloth.
When the equipment is to remain idle 

2. 

for longer than 20 days, prepare the 

engine for storage as follows:

Change engine oil and empty fuel 

a. 

tank.
Either leave fuel tank empty or 

b. 

refill fuel tank with fresh unleaded 

gasoline mixed with a fuel stabilizer 

intended for long term engine stor-

age (not included).  After filling, run 

engine for about 5-10 minutes to cir-

culate the treated gasoline through 

the carburetor.  Wait for engine to 

cool before proceeding.
Clean out area around spark plug.  

c. 

Remove spark plug and pour one 

tablespoon of engine oil into cylinder 

through spark plug hole.
Reinstall spark plug, but leave spark 

d. 

plug wire disconnected.
Pull recoil starter to distribute oil in 

e. 

cylinder.  Stop after one or two revo-

lutions when you feel the piston start 

the compression stroke (when you 

start to feel resistance).
Disconnect battery cables.

f. 

Apply a thin coat of rust preventive oil 

3. 

to all uncoated metal parts.
Cover and store in a dry, well-ventilat-

4. 

ed area out of reach of children.
Before starting the engine after stor-

5. 

age, keep in mind that untreated gas-

oline will deteriorate quickly.  Drain 

the fuel tank and filter, and change 

to fresh fuel if untreated gasoline has 

been sitting for a month, if treated 

gasoline has been sitting beyond the 

fuel stabilizer’s recommended time 

period, or if the engine does not start 

properly.

Содержание 97906

























Отзывы: