background image

Page 19

SKU 97906

For technical questions, please call 1-800-444-3353.

generator partS LiSt

part

description

qty

1a

Battery Charging Cord (not 

shown)

1

2a

Fuel Tank Cap

1

3a

Fuel Tank Filter

1

4a

Flange Bolt M6x20

4

5a

Gasket

4

6a

Screw Gasket

4

7a

Anti-Vibration Gasket

4

8a

Fuel Tank

1

9a

Fuel Valve

1

10a Fuel Pipe Clamp

2

11a Oil Pipe

1

12a Engine

1

13a Exhaust Pipe Gasket

1

14a Exhaust Pipe

1

15a Lock Nut M8

2

16a Flange Bolt M6x12

2

17a

Muffler Gasket

1

18a

Muffler

1

19a Flange Bolt M6x12

1

20a Front Cover

1

21a Gasket

4

22a Flange Bolt M8x20

4

23a Rotor Assembly

1

24a Stator Assembly

1

25a Wiring Cover

1

26a Rear Cover

1

27a

Rectifier

1

28a Gasket

4

29a Spring Gasket

4

generator partS LiSt

part

description

qty

30a Bolt

4

31a Gasket

1

32a Spring Gasket

1

33a Bolt M8x170

1

34a Magneto Cover

1

35a Gasket

2

36a Spring Gasket

2

37a Bolt M5x8

2

38a Lock Nut M8

6

39a Gasket

8

40a Spring Gasket

8

41a Bolt M8x40

8

42a Cushion

2

43a Frame

1

44a Anti-Vibration Feet

4

45a Flex Tube

1

46a Circuit Cover

1

47a Bolt M4x10

2

48a Capacitor

1

49a Bolt M4x10

1

50a Panel

1

51a Bolt M6x25

4

52a Power Switch

1

53a AC Circuit Protector

1

54a AC Outlet

2

55a Grounding Point

1

57a Battery Charging Socket

1

59a DC Circuit Protector

1

60a Rubber Gasket

1

61a Bracket for Capacitor

1

pLeaSe read the FoLLowing careFuLLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY 

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR 

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT 

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS 

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/

OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD 

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE 

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE 

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER 

INSTALLATION OF REPLACEMENT PARTS THERETO.

record product’s Serial number here: 
note:

  If product has no serial number, record month and year of purchase instead.

note:

  Some parts in both parts lists are listed and shown for illustration purposes only, 

and are not available individually as replacement parts.

REV 09b

Содержание 97906

























Отзывы: