background image

SKU 55594

For technical questions, please call 1-800-444-3353.

Page 4

11.

Dress properly.  Do not wear loose clothing or jewelry.  Contain long hair.
Keep your hair, clothing, and gloves away from hot or moving parts.

  Loose

clothes, jewelry, or long hair can be caught in hot or moving parts.  

(See page 5,

number 3, for recommended safety clothing.)

12.

Avoid accidental starting.

  

Be sure the Power Switch is off before plugging

in. 

 Plugging in welding equipment with the Power Switch on invites accidents.

13.

Remove adjusting keys or wrenches before turning on the welding
equipment.  

A  wrench or a key that is left attached to an electrically charged

part of the welding equipment may result in personal injury.

14.

Do not overreach.  Keep proper footing and balance at all times. 

 Proper

footing and balance enables better control of the welding equipment in
unexpected situations.

15.

Use safety equipment.  Always wear eye protection.  

Dusk mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.

TOOL USE AND CARE

16.

Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform.

  Holding the work by hand or against your

body is unstable and may lead to loss of control.

17.

Do not force the welding equipment.  Use the correct equipment for your
application. 

 The correct equipment will do the job better and safer at the rate for

which it is designed.

18.

Do not use the power tool if the Power Switch does not turn it on or off.

Any equipment that cannot be controlled with the Power Switch is dangerous and
must be replaced.

19.

Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the welding equipment.

Such preventive safety measures reduce the risk of starting the welding
equipment accidentally.

20.

Store idle welding equipment out of reach of children and other untrained
persons.  

Welding equipment is dangerous in the hands of untrained users.

Содержание 55594























Отзывы: