background image

SKU 55594

For technical questions, please call 1-800-444-3353.

Page 8

16.

Do not touch the welding wire if you are in contact with the workpiece,
ground, or another welding wire from a different machine.

17.

Do not allow the welding wire to touch earth ground.  

Accidental earth

discharges may cause overheating and fire hazards.

18.

Do not pass equipment cables through or near lifting chains, crane cables,
or any electrical lines.

19.

Never use the Welder near water.  

Ensure that the surrounding area and cutting

objects are dry.  Do not spray water or other liquids on or near the Welder.

20.

Avoid all direct contact between the skin and wet garments and metal parts
under electrical power.  

Check that gloves and protective clothing are dry.

21.

Never leave the Welder unattended when it is plugged into an electrical
outlet.  

 Make sure to unplug it from its electrical outlet before leaving the area.

22.

Do not unplug the Welder by pulling on the Power Cord.  Keep the Power
Cord away from heated surfaces.

23.

Always turn off the Welder in the event of a power failure.

24.

Significant DC electrical voltage exists after turning off and unplugging the
Welder.  

Discharge the electrode to ground before handling.

25.

Performance of this Welder may vary depending on variations in local line
voltage.  

Extension cord usage may also affect tool performance.

26.

Always turn off the Welder and unplug the unit from its electrical outlet
before performing any inspection, maintenance, or cleaning procedures.

27.

Use the right tool or attachment for the right job.  

Do not attempt to force a

small tool or attachment to do the work of a larger industrial tool or attachment.
There are certain applications for which this product was designed.  It will do the
job better and more safely at the rate for which it was intended.  Do not modify
this product, and do not use this product for a purpose for which it was not
intended.

28.

         

WARNING!   

The brass components of this product contain lead, a

chemical known to the State of California to cause birth defects (or other
reproductive harm).  

(California Health & Safety code 25249.5, et seq.)

Содержание 55594























Отзывы: