background image

Straight

Outdoor gas appliance is not intended to be installed in 
or on a boat.
Outdoor gas appliance is not intended to be installed in 
or on an RV.
Never attempt to attach this grill to the self-contained LP 
gas system of a camper trailer or motor home.
Do not use grill until leak-tested.
If a leak is detected at any time, 

STOP

 and call the fire 

department.
If you cannot stop a gas leak 

IMMEDIATELY

 close LP 

cylinder valve and call LP gas supplier or your fire 
department!

WARNING

DANGER

Do not insert any tool or foreign object into the valve outlet 

or safety relief valve.  You may damage the valve and 
cause a leak.  Leaking propane may result in explosion, 
fire, severe personal injury, or death.

Hold coupling nut and regulator 
as shown for proper connection 
to LP cylinder valve.

Connecting Regulator to the LP Cylinder (Con’t.)

6. Turn the coupling nut clockwise and tighten to a 

Full Stop

.  

The regulator will seal on the back-check feature in the LP 
cylinder valve, resulting in some resistance.  

An additional 

one-half to three-quarters turn is required to complete the 
connection.  Tighten by hand only - do not use tools.

NOTE:

If you cannot complete the connection, disconnect regulator and 

repeat steps 5 and 6.  If you are still unable to complete the 
connection, 

do not use this regulator!

Never remove threaded orifice 
at end of valve during leak 
testing of valves.

Leak Testing Valves, Hoses and Regulator

1.

Turn all control knobs to the OFF position.

2. Be sure regulator is tightly connected to LP cylinder.

3. Completely open LP cylinder valve by turning hand wheel 

counterclockwise.  If you hear a 

rushing sound

, turn gas off 

immediately.  There is a major leak at the connection.  

Correct 

before proceeding.

4. Brush soapy solution onto areas circled below.

5. If “growing” bubbles appear there is a leak.  Close LP cylinder 

valve immediately and retighten connections.  If leaks cannot 
be stopped do not try to repair.  Call for replacement parts.  
Order new parts by giving the serial, model number and name 
and part number of items needed (see parts list) to the Grill 
Service Center at  1-888-430-7870.

6. Always close LP cylinder valve after performing leak test by 

turning hand wheel clockwise.

Содержание Heatwave 2218932





























Отзывы: