manualshive.com logo in svg

Champion UH130 M4, Инструкция по установке и эксплуатации

Поделиться
Скачать
Champion UH130 M4 Скачать руководство пользователя страница 95

85

! ATTENTION ! 

DOOR LEFT OPEN DURING WASH CYCLE 

If the dishwasher door is left open for more than 5 seconds during the wash mode 

the dishwasher cycle will reset to the beginning of the selected wash cycle.    

! ATTENTION ! 

RINSE SENTRY MODE WILL EXTEND WASH CYCLE TIME 

In the event that the final rinse temperature inside the booster tank has not reached 

180-195ºF/82-91ºC after the wash cycle, the rinse sentry will extend the wash cycle time until 

the booster reaches 180-195ºF/82-91ºC.  If the proper temperature is not reached within 5 

minutes, the machine will leave the rinse sentry mode and complete the cycle.       

Operation - UH330B

Model UH330B - Operation

9.  The HEAVY cycle is selected by pushing the cycle button twice.  The HEAVY green 

indicator light will flash for 15 seconds. Pressing the START button before the flashing 

HEAVY indicator light stops flashing starts the heavy wash cycle of approximately 4-1/2 

minutes long. The HEAVY green indicator light will come on and the green indicator light 

above the start switch will illuminate indicating the machine is in the wash mode.  

10.  Opening the door during a cycle will stop the dishwasher.  The cycle will resume  

automatically if the dishwasher door is closed within 5 seconds.  If the door is open for 

more than 5 seconds the cycle will start from the beginning of the cycle. 

11.  The final rinse cycle begins at the end of the wash cycle. The machine drains and  

retains a portion of the final rinse water for the next wash cycle. 

12.  Check the rinse temperature gauge during the final rinse. It must indicate a minimum of 

180-195ºF/82-91ºC.  The final rinse water is retained for the next wash cycle. 

13.  When the green cycle light goes out, open the door and remove the rack of clean wares.

Wash Mode 

(continued) 

Rinse Sentry Mode 

Содержание UH130 M4







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды