Champion UH130 M4 Скачать руководство пользователя страница 52

Страница: 52 / 166

Installation - Model UL130

Pump Priming - Detergent, Rinse-aid and Sanitizer Dispensing Pumps

UL130 Control Panel

PRIME

OFF/DRAIN

POWER

START

RINSE AID

DETERGENT

SANITIZER

160

140

120

170

180

190

200

220

100

105

NSF

EXT. WASH

D E L I M E

1. Make sure the chemical containers are full and the correct pick-up tubes are in their

containers.

2. Turn the dishwasher power switch ON. The switch will illuminate and the dishwasher

will fill with water.

3. Refer to the illustration below and note the two momentary push buttons provided to

prime the detergent, sanitizer and rinse aid pumps.

4. Open the dishwasher door and observe the inlet chute on the rear right-hand side of

the wash tank.

5. Push and hold the prime push button UP to the DETERGENT position until detergent is

observed entering the wash tank compartment. Release the push button.

6. Push and hold the same push button DOWN until sanitizer is observed entering the

wash tank compartment. Release the push button.

7. Push and hold the other push button UP to the RINSE AID position until rinse-aid

is observed entering the wash tank compartment. Release the push button.

8. Priming is complete.

PRIME

RINSE AID

DETERGENT

SANITIZER

! VERY IMPORTANT !

The chemical dispensing pumps must be primed before operating the dishwasher and

whenever the chemical container is changed.

Содержание UH130 M4







































































































































































Результаты поиска

Содержание UH130 M4

Отзывы:

Бренды по названию

Популярные бренды

Champion UH130 M4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UH130 M4

Отзывы:

Бренды по названию

Популярные бренды