Champion UH130 M4 Скачать руководство пользователя страница 20

Страница: 20 / 166

Water Connections - UH130, UH130B, UH230, UH230B

1. All models have a 6 ft. flexible hot water fill hose with a 3/4" female garden hose connector.

2. A 1/2" or larger main incoming supply line must be installed to the dishwasher.

3. A 1/2" or larger shut-off valve should be installed in the main water supply, as close to the

dishwasher as possible for servicing.

FOR UH130: The UH130 has a built-in flow control. The flowing incoming hot water supply

pressure must be between 25-95 psi. The hot water supply must provide a minimum of

180°F/82°C, measured at the dishwasher.

FOR UH130B: The UH130B has a built-in flow control. The flowing incoming hot water

supply pressure must be between 25-95 psi. The hot water supply must provide a minimum

of 140°F/60°C, measured at the dishwasher for 40°F/22°C rise booster or 110°F/43°C for

70°F/39°C rise booster.

4. FOR UH230: The hot water supply must provide a minimum of 180°F/82°C, measured at the

dishwasher.

A pressure regulating valve, PRV, (supplied), must be installed after the shut-off

service valve if the incoming flow pressure exceeds 20-22 psi.

FOR UH230B: The hot water supply must provide a minimum of 140°F/60°C, measured at the

dishwasher for 40°F/22°C rise booster or 110°F/43°C for 70°F/39°C rise booster.

A pressure regulating valve, PRV, (supplied), must be installed after the shut-off service valve if

the incoming flow pressure exceeds 20-22 psi.

5. A water hardness of 3 grains/gal (US) [5.3 mg/L] or less is recommended. Excessively hard

water will negatively impact wash results.

! VERY IMPORTANT !

Make sure the flexible water supply and drain hoses are not kinked.

Plumbing connections must allow the machine to be pulled out for service and cleaning.

Plumbing connections must comply with national, provincial local plumbing and sanitary

codes. Only qualified service personnel familiar with food service equipment should install

the machine.

The installing plumber must thoroughly flush the water supply line to remove all debris

BEFORE connecting the water supply line to the machine.

Installation - Model UH130, UH130B, UH230, UH230B

Содержание UH130 M4







































































































































































Результаты поиска

Содержание UH130 M4

Отзывы:

Бренды по названию

Популярные бренды

Champion UH130 M4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UH130 M4

Отзывы:

Бренды по названию

Популярные бренды