manualshive.com logo in svg

Champion UH130 M4, Инструкция по установке и эксплуатации

Поделиться
Скачать
Champion UH130 M4 Скачать руководство пользователя страница 34

24

Operation - Model UH130, UH130B 

Operation - UH130, UH130B Only

Wash Temperature  

Digital Display

Final Rinse Temperature  

Digital Display

Prime 

Push button

In-cycle Light

Start  

Push button

ON-OFF/DRAIN 

Power Switch

UH130B Control Panel

WASH

RINSE

PRIME

DETERGENT

RINSE AID

OFF/DRAIN

ON

POWER

START

TEMPERATURE

1 8 0

1 5 0

1.  Close the dishwasher front door.
2.  Push the dishwasher Power Switch UP to turn the power ON.
3.  The power switch will illuminate and the machine will fill with water.
4.  Wait until the wash temperature gauge indicates a minimum of 150ºF/66ºC. 

 

PLACE AN EMPTY DISHRACK IN THE MACHINE AND RUN THE FIRST  

CYCLE EMPTY TO HEAT THE WASH TANK INTERIOR.  

5.  Load the dish rack into the machine.  Wash one dish rack at a time.
6.  Close the door, then press the START BUTTON for 1 second.  The green in-cycle 

light will illuminate and the wash cycle will begin.  The total cycle is approximately 

141 seconds. 

7.  Opening the door during a cycle will stop the dishwasher.  If the door is open more than 5 

seconds the cycle will restart from the beginning, if open less than 5 seconds the cycle 

will resume where it left off when the dishwasher door is closed.

8.  The final rinse cycle begins at the end of the wash cycle. The machine drains and then  

refills with fresh water hot water. Check the rinse temperature gauge during the final rinse. 

It must indicate a minimum of 180-195ºF/82-91ºC.  The final rinse water is retained 

for the next wash cycle.

9.  When the green cycle light goes out, open the door and remove the rack of clean wares.

Normal Wash Mode  

! ATTENTION ! 

DOOR LEFT OPEN DURING WASH CYCLE 

If the dishwasher door is left open for more than 5 seconds during the normal wash mode, then 

the dishwasher cycle will reset to the beginning of the normal wash cycle.    

! ATTENTION ! 

RINSE SENTRY MODE WILL EXTEND WASH CYCLE TIME 

In the event that the final rinse temperature has not reached 180-195ºF/82-91ºC after the

wash cycle, the rinse sentry will extend the wash cycle time until the booster reaches 

180-195ºF/82-91ºC.  If the proper temperature is not reached within 5 minutes, the machine 

will leave the rinse sentry mode and complete the cycle.       

Содержание UH130 M4







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды