manualshive.com logo in svg

Champion UH130 M4, Инструкция по установке и эксплуатации

Поделиться
Скачать
Champion UH130 M4 Скачать руководство пользователя страница 43

33

Model UH130, UH130B, UH230, UH230B - De-liming

Follow the procedures below to de-lime the UH230, UH230B dishwasher.

1.  Open the dishwasher door and remove any dish racks.

2.  Turn the power switch on the dishwasher to the ON position.

3.  Remove the detergent and rinse-aid chemical supply tubing from their chemical supply 

containers.

4.  Place the tubing in a container of hot water.

5.  Press and hold the prime switch UP in the DETERGENT position to flush the detergent from 

the supply tubing.  Release the switch.

6.  Press and hold the prime switch DOWN in the RINSE AID position to flush the rinse-aid 

from the supply tubing. Release the switch.

7.  Turn the dishwasher power switch to OFF/DRAIN to drain the wash tank. The green cycle 

light will go out in about 2 minutes. 

8.  Always wear eye protection, rubber gloves and protective clothing when handling 

chemicals.

 Open the door and carefully add the de-liming chemical to the wash tank in 

accordance with your chemical supplier's instructions.  Be careful to avoid splashing.

9.  Close the door and press the EXT WASH/DELIME switch three times. The EXT WASH/

DELIME indicator light will illuminate and the machine will run for 23 minutes. 

10.  Check the de-liming results and if scale is still present repeat steps 7-9.

11.  Push the power switch ON to refill the machine and return the dishwasher to normal 

operation.

12.  Return chemical supply tubing to their containers and prime the chemical lines.

UH230 and UH230B De-liming Procedure

Read and Follow the De-liming Cautions and Warnings  

on page 32 before de-liming the machine..

Содержание UH130 M4







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды