manualshive.com logo in svg

Champion UH130 M4, Инструкция по установке и эксплуатации

Поделиться
Скачать
Champion UH130 M4 Скачать руководство пользователя страница 94

84

Operation - Model UH330B

UH330B Control Panel  

Operation 

- 

Model UH330B

1.  Close the door.
2.  Push the dishwasher ON-OFF/DRAIN switch UP to turn the power ON.
3.  The power switch will illuminate and the machine will fill with water.
4.  Wait approximately 30 minutes until the wash temperature gauge indicates a minimum of 

150ºF/66ºC.

 

5.  Scrap the wares to remove large food particles.
6.  Load the dish rack into the machine.  Wash one dish rack at a time. 

 

 

 

 

 

 

 

 

 

 

 

7.  The NORMAL cycle setting is the default cycle and does not have a green indicator light.  

The normal cycle is approximately 2-1/2 minutes long. 

8.  The EXTRA cycle is selected by pushing the cycle button once.  The EXTRA green indicator 

light will flash for 15 seconds. Pressing the START button before the flashing EXTRA ind-

icator stops flashing starts a EXTRA wash cycle of approximately 3-1/2 minutes long. The 

EXTRA green indicator light will come on. and the green indicator light above the start 

switch will illuminate indicating the machine is in the wash mode. 

The illustration below shows the operator controls and temperature displays for the UH330B.

PRIME

DETERGENT

RINSE AID

START

CYCLE

WASH

RINSE

TEMPERATURE

1 8 0

1 5 0

OFF/DRAIN

ON

POWER

NORMAL

EXTRA

HEAVY

Cycle Selector 

Push button

Wash Temperature  

Digital Display

Final Rinse Temperature  

Digital Display

Prime 

Push button

Time Select 

Lights

Start  

Push button

ON-OFF/DRAIN 

Power Switch

Cycle Light

Wash Mode

START

CYCLE

EXTRA

HEAVY

NORMAL

Push the Cycle button once for Extra Cycle. 

Push twice for Heavy Cycle. 

Push the Cycle button three times to cancel 

the selection and return to Normal Cycle.

(continued on next page)

Содержание UH130 M4







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды