Champion UH130 M4 Скачать руководство пользователя страница 31

Страница: 31 / 166

Model UH130, UH130B, UH230, UH230B - Installation

Detergent and Rinse-aid Dispensing Pumps - Pump and Fill Adjustments

UH130, UH130B and UH230, UH230B

To adjust the amount of chemicals dispensed

by the pumps:

1. Make sure the chemical containers are full and

the pick-up tubes are in their proper containers.

3. Turn the dishwasher power switch ON.

The switch will illuminate and the dishwasher

will fill with water.

4. Run a normal dishwasher cycle and test

detergent and rinse-aid concentrations

according to the chemical supplier's

instructions.

CAUTION:

Excessive pressure to the potentiometers when

adjusting can result in bent or broken adjusting

screws.

5. Each dispensing pump has a clearly marked

adjustment screw. Turn the screw CW to

increase the run time of the dispensing pump

and CCW to reduce the run time.

UH130, UH130B only

To adjust the tank fill:

1. The fill adjustment screw will provide a

small change in the tank water level.

2. If a large adjustment is needed, check the

incoming water pressure and make sure the fill

hose is not kinked.

3. If the above items are okay then the size

of the incoming water supply should be

checked. The incoming water supply line must

be a minimum of 1/2" or larger.

Refer to the photo below:

Fill Adjustment

For UH130, UH130B

Only

Use a 4mm

blade

screwdriver

Содержание UH130 M4







































































































































































Результаты поиска

Содержание UH130 M4

Отзывы:

Бренды по названию

Популярные бренды

Champion UH130 M4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UH130 M4

Отзывы:

Бренды по названию

Популярные бренды