manualshive.com logo in svg

Champion UH130 M4, Инструкция по установке и эксплуатации

Поделиться
Скачать
Champion UH130 M4 Скачать руководство пользователя страница 36

26

! ATTENTION ! 

DOOR LEFT OPEN DURING WASH CYCLE 

If the dishwasher door is left open for more than 5 seconds during the normal wash mode, then 

the dishwasher cycle will reset to the beginning of the normal wash cycle.    

! ATTENTION ! 

RINSE SENTRY MODE WILL EXTEND WASH CYCLE TIME 

In the event that the final rinse temperature has not reached 180-195ºF/82-91ºC after the

wash cycle, the rinse sentry will extend the wash cycle time until the booster reaches 

180-195ºF/82-91ºC.  If the proper temperature is not reached within 5 minutes, the machine 

will leave the rinse sentry mode and complete the cycle.       

UH130B and UH230B Rinse Sentry Mode

 

Extended Wash Mode 

Model UH230, UH230B Only

The Extended Wash Mode is used to wash heavily soiled items such as pots, pans and other 

wares that require more washing time than the standard 90 second Normal Wash Mode. 

The dishwasher will remain in the Extended Wash Mode until the operator exits the mode or 

a maximum of 15 minutes, whichever occurs first. 

1.  Load a dish rack into the dishwasher, close the door and press the START button.
2.  The green in-cycle light will illuminate and the dishwasher will begin a normal wash cycle.
3.  Wait 10 seconds for the detergent to enter the wash compartment before pressing the  

EXT WASH button. 

 

 

 

 

 

 

 

 

 

 

 

 

4.  Press the EXT WASH button to place the dishwasher in the Extended Wash Mode.
5.  The green extended wash light will illuminate indicating that the machine is in the  

Extended Wash Mode.

6.  The dishwasher will continue to wash for a maximum of 15 minutes unless the operator 

presses the EXT WASH button again.

7.  Press the EXT WASH button.  The green extended wash light will go out indicating that 

the dishwasher has returned to the Normal Wash Mode.

8.  The dishwasher will finish the wash cycle and perform a final rinse of the wares. 

EXT WASH

Press the EXT WASH button to place the 

machine into the extended wash mode to 

clean heavily soiled wares. 

Operation - 

Model UH130, UH130B and UH230, UH230B

Содержание UH130 M4







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды