Champion Global Power Equipment 100416 Скачать руководство пользователя | Manualshive

Страница: 36 / 41

background image

100416 - 8000W TRI-FUEL PORTABLE GENERATOR

TROUBLESHOOTING

36

TROUBLESHOOTING

Problem

Cause

Solution

Engine will not start.

No fuel.

Add fuel.

Faulty spark plug.

Clean and adjust spark plug or replace.

Low oil level.

Fill crankcase to the proper level.

Place generator on a flat, level surface.

Spark plug wire loose.

Attach wire to spark plug.

Fuel valve is closed.

Open fuel valve.

EZ Start dial OFF.

Turn EZ Start dial ON.

Old fuel or water in fuel.

Drain fuel and replace with fresh fuel.

Flooded with fuel.

Let unit stand for 10 mins.

CO Shield

®

module has been removed or

tampered with.

Re-install module or contact technical support.

Engine starts but runs roughly.

Choke in the wrong position.

Move choke until it stops under RUN position or
push in completely.

Dirty air filter.

Clean or replace air filter.

Dirty fuel valve.

Clean the fuel valve.

Clogged spark arrestor.

Clean spark arrestor.

Engine will not start electrically.

Generator battery is dead.

Recharge generator battery.

Engine shuts down during operation.

Out of fuel.

Fill fuel tank.

Low oil level.

Fill crankcase to the proper level. Place generator
on a flat, level surface.

If equipped, CO Shield

®

shutoff due to

accumulating carbon monoxide if the red
LED light blinks on the panel.

Move generator to an open, outdoor area. Point
exhaust away from people and buildings. Move
to fresh air and get medical help if sick, dizzy, or
weak.

If equipped, CO Shield

®

shutoff due

system fault if the yellow LED light blinks
on the panel.

Start to confirm yellow LED light blinks when/if
generator shuts off. If CO Shield continues sense
the fault and shuts off, contact technical support.

Clogged spark arrestor.

Clean spark arrestor.

Engine starts and shuts off right away.

If equipped, CO Shield

®

shutoff due to

accumulating carbon monoxide if the red
LED light blinks on the panel.

Move generator to an open, outdoor area. Point
exhaust away from people and buildings. Move
to fresh air and get medical help if sick, dizzy, or
weak.

If equipped, CO Shield

®

shutoff due

system fault if the yellow LED light blinks
on the panel.

Start to confirm yellow LED light blinks when/if
generator shuts off. If CO Shield continues sense
the fault and shuts off, contact technical support.

Both CO Shield

®

LEDs not blinking 8

times upon start up.

Starting the generator within 1 minute
after being manually shutoff, not a CO
shutoff event.

Wait 1 minute before trying to restart the
generator. The LEDs should then blink eight (8)
times.

Generator cannot supply enough power
or overheating.

Generator is overloaded.

Review load and adjust. See “Connecting
Electrical Loads.”

Dirty air filter.

Clean or replace air filter.

Choke in wrong position.

Move choke until it stops under RUN position or
push in completely.

«
...
34
35
36
37
38
...
»

Содержание 100416










































Отзывы:

Нет отзывов

Похожие инструкции для 100416

Бренд: Pulsar Страницы: 39

Бренд: Sencor Страницы: 10

Бренд: VICI DBS Страницы: 41

Бренд: Jung Страницы: 10

Бренд: Schumacher Страницы: 7

Бренд: Troy-Bilt Страницы: 2

Бренд: Troy-Bilt Страницы: 28

Бренд: Simoco Страницы: 45

Бренд: Durabrand Страницы: 28

HUBNER BERLIN GTF 7

Бренд: Baumer Страницы: 24

Бренд: PASCO Страницы: 9

Бренд: Magnasonic Страницы: 8

Бренд: Magnasonic Страницы: 10

45416 Assembly and

Бренд: Chicago Electric Страницы: 11

Бренд: Audiovox Страницы: 33

Бренд: Audiovox Страницы: 29

Бренд: Westinghouse Страницы: 12

Бренд: oneConcept Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды