Chamberlain Motorlift ML700, Инструкция по эксплуатации

Страница: 72 / 142

en
7
To Erase all Remote Control Codes
To deactivate any unwanted remote, first erase all codes: Press and
hold the orange “learn” button on opener until the learn indicator light
goes out (approximately 6 seconds). All previous codes are now
erased. Reprogram each remote or keyless entry you wish to use.
3-Channel Remote:
If provided with your garage door opener, the large button is factory
programmed to operate it. Additional buttons on any rolling code 3-
channel remote or mini-remote can be programmed to operate this or
other rolling code garage door openers.
NOTE: Only the original remote controls from the manufacturer should
be used. Remote controls that may look very similar, but do not
originate from the manufacturer are not compatible. Such third-party
remotes create malfunctions such as automatic opening, and the
guarantee on the function and safety expires.
Special Features
A. Door within a door connection
Open light lens. Locate auxiliary quick connect terminals. Insert
bell wire into quick connect terminals 8 and 7.
B. Flashing light connection
The flashing light can be installed anywhere. Connect light leads
to quick connect terminals 6 and 5. Terminal 5 is ground.
C. 24 V, max 200mA
D. Partial opening
Description of feature:
The pedestrian , ventilation or pet opening position is an adjustable
second stop position between the fully opened and fully closed posi-
tion of the garage door. Partial Opening can be executed via control
panel (78EML) or a 3-channel remote control. For activation and
adjustment a wired control panel 78EML is mandatory. The garage
door operator must be fully operable and completely installed.
Additional accessories, which are not included, may be required for
operation and programming.
Wiring 78EML(optional):
The wired control panel must be installed the usual way. Please refer
to your garage door operator manual.
The LED on the control panel must be illuminated.
Activation:
1. The wall control is connected to the opener and the LED is
illuminated.
2. The garage door operator opens the door complete if the white
button on the control panel is used.
3. Move the garage door to the desired door height.
4. Press and hold the light button on the Door Control Panel.
5. Press and hold the “Lock” (PED) button on the Door Control Panel.
6. Keep both buttons pressed (~10 sec.) and wait until the garage door
operator light flashes once, or until you hear a click ( if no light bulb
installed).
7. Completed
8. Test the function by using the “Lock” (PED) button on the control
panel.
Delete/Deactivate:
1. The wall control is connected and the LED on the panel is
illuminated.
2. Move the garage door to the fully closed position.
3. Press and hold the light button on the Door Control Panel.
4. Press and hold the “Lock” (PED) button on the Door Control Panel.
5. Keep both buttons pressed (~10 sec..) and wait until the garage
door operator light flashes once, or until you hear a click ( if no light
bulb installed).
6. Completed
Programming the remote control:
1. Full opening of the door is programmed as usual i.e. using the
square SMART button at yout operator. If this information is not
enough please consult the operator instructions.
2. Select a second button on your control that should partially open
your garage door.
1. Push and hold the selected button on your remote control.
2. Push and hold the light Button
3. Push and hold the large white door control button.
• Keep all buttons pressed and wait until the garage door operator
light flashes once, or until you hear a click (if no light bulb
installed).
• Completed.
3. Continue with another remote controle if required.
Note:
Any programmed remote button reduces the number of memory regis-
ters.
28
Program your Keyless Entry
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or leave
garage while door is in motion. Do not allow children to operate
push button(s) or remote(s). Do not allow children to play near
the door.
NOTE: Your new Keyless Entry must be programmed to operate your
garage door opener.
Program the Receiver to Match Additional Remote Control Code
Using the orange “LEARN” Button:
1. Press and release the orange “learn” button (1) on opener. The
learn indicator light will glow steadily for 30 seconds.
2. Within 30 seconds, enter a four digit personal identification number
(PIN) of your choice on the keypad (2), then press and hold the
ENTER button.
3. Release the button when the opener light blinks (3). It has learned
the code. If the light bulb is not installed, two clicks will be heard.
NOTE: This method requires two people if the Keyless Entry is already
mounted outside the garage.
Using the Multi-Function Door Control:
1. Enter a four digit personal identification number (PIN) of your choice
on the keypad, then press and hold ENTER.
2. While holding the ENTER button, press and hold the LIGHT button
on the Multi-Function Door Control.
3. Continue holding the ENTER and LIGHT buttons while you press
the push bar on the Multi-Function Door Control (all three buttons
are held).
4. Release buttons when the opener light blinks. It has learned the
code. If the light bulb is not installed, two clicks will be heard.